Baroness LM551B Скачать руководство пользователя страница 146 | Manualshive

Страница: 146 / 172

background image

1

Bolt, heat-treated

Securely place the jack beneath the jack-up
point of the pivot, and then raise it until the
tires lift off the ground.
"Jack-Up Points" (Page 5-22)
Remove the bolts.
Remove the tire from the wheel mounting
base.

Important

Tighten the bolts in the tightening order
(diagonally).

For installing the rear tire, reverse the
removing procedure.

Adjustment of Belt Tension

Warning

Be sure to stop the engine before adjusting
the belts.

Important

Before making sure of belt tension, rotate the
belt several times.

If the belt becomes slack due to frequent use, it
may jump or slip.
In addition, if it is overtightened, it may wear
prematurely.
If necessary, adjust it, and always check the
belt for appropriate tension.

Fan Belt

Press the middle of the belt with your finger
to check the belt tension.
The belt tension is appropriate when the
belt slacks by approximately 10.0 mm (0.39
in) when you apply a force of 98 N (10 kgf)
to the belt at the middle point between the
pulleys.

2.

3.
4.

1.

If the belt tension is incorrect, loosen bolt A
and bolt B (securing the alternator), and
then move the alternator to adjust the
tension.

2

5

3

4

1

A

mzdn8n-004

Fan Belt_001

1

Fan Belt

2

Blade

3

Alternator

4

Bolt A

5

Bolt B

A

10 mm (0.39 in)

2.

LM551B

Maintenance

Page 5-32

Maintenance Work

«
...
144
145
146
147
148
...
»

Содержание LM551B













































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LM551B

Бренд: Jacobsen Страницы: 46

Бренд: Jacobsen Страницы: 70

Бренд: Jacobsen Страницы: 26

Бренд: Jacobsen Страницы: 247

Greens King V Plus

Бренд: Jacobsen Страницы: 94

Groom Master II

Бренд: Jacobsen Страницы: 104

Бренд: Jacobsen Страницы: 144

Бренд: Elem Garden Technic Страницы: 58

Бренд: Exmark Страницы: 4

Бренд: Villager Страницы: 128

Бренд: RedMax Страницы: 40

Бренд: Walker Страницы: 84

Бренд: Poulan Pro Страницы: 32

Бренд: Troy-Bilt Страницы: 48

Бренд: Honda Страницы: 24

Бренд: Cramer Страницы: 184

Бренд: Cub Cadet Страницы: 20

Бренд: Craftsman Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды