manualshive.com logo in svg

Baroness LM18GB, Руководство по эксплуатации для владельца

Поделиться
Скачать
Baroness LM18GB Скачать руководство пользователя страница 32

Fuel Supply

Danger

Danger

Do not supply fuel above FULL level of the
fuel gauge.
If you supply too much fuel, it might overflow
from the fuel cap when you travel or work on a
slope.

Warning

Keep fire away while refueling.
Do not smoke while refueling.

Caution

Pay attention not to touch hot parts.

If the fuel gauge on the fuel tank indicates a
level close to EMPTY, supply fuel (gasoline)
at your earliest convenience.
The fuel tank capacity is approximately 2.3
dm

3

 (2.3 L).

2

3

1

2e4emp-005

Fuel Supply_001

1

Fuel tank

2

Tank cap

3

Fuel gauge

Oil Leakage

Inspection of Oil Leakage

After approximately 50 hours of operation,
some joints may be loosened and oil and
grease may leak.
Be sure to retighten the parts.
Check the bottom of the machine for oil and
grease leakage.

LM18GB

・

LM56GB/LM66TB

Handling Instructions

Page 5-8

Inspection Before Use

Содержание LM18GB


















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды