manualshive.com logo in svg

Baroness LM18GB, Руководство по эксплуатации для владельца

Поделиться
Скачать
Baroness LM18GB Скачать руководство пользователя страница 31

Replacement of Engine Oil

For details on handling the engine, please
refer to the Engine's Owner's Manual.

Warning

When you replace the engine oil, be sure to
drain it into a bowl and discard it in
accordance with local laws and regulations.

Caution

Be careful with hot oil, which could cause
burns if it contacts your skin.

Important

Be sure to use engine oil that is classified as
API Service Grade SE or higher, with an SAE
Viscosity that is appropriate for the operating
environment (ambient temperature).

Important

Screw the oil level gauge firmly.

Replace the engine oil more frequently if the
engine oil is contaminated, and especially if
you use the machine in dusty areas or
operate the engine at high loads or in high
temperatures.

Move the machine onto a level surface,
stop the engine.
Remove the drain plug while the engine oil
is warm, and then drain the engine oil into a
bowl.
Replace the drain plug in the engine.
Remove the oil level gauge.
Through the oil filling port, supply new
engine oil.
The engine oil quantity is approximately 0.6
dm

3

 (0.6 L).

1.

2.

3.
4.
5.

Check the engine oil level.

1

2

gui678-016

Replacement of Engine Oil_001

1

Oil level gauge (Oil filling port)

2

Drain plug

After checking the oil level with the oil level
gauge, add more engine oil if it is
insufficient.
Securely tighten the oil level gauge.
It will take a while for the supplied engine oil
to descend into the crank case.
Check the oil level again 5 to 10 minutes
after filling the engine oil.

Fuel

Inspection of Fuel Quantity

With the machine on a level surface, observe
the fuel gauge on the fuel tank to check the
fuel level.

1

A

B

guc5f6-010

Inspection of Fuel Quantity_001

1

Fuel gauge

A

FULL

B

EMPTY

6.

7.

8.
9.

Handling Instructions

LM18GB

・

LM56GB/LM66TB

Handling Instructions

Page 5-7

Inspection Before Use

Содержание LM18GB


















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды