manualshive.com logo in svg

Baroness GM2810A, Руководство по эксплуатации для владельца, Страница: 68 / 155

Поделиться
Скачать
Baroness GM2810A Скачать руководство пользователя страница 68

You can operate this machine to perform
the regeneration. (The fault diagnostic tool
is not required.)
Automatic regeneration is activated only
when the auto regeneration inhibit switch
set to the "Auto regeneration mode".
Automatic regeneration is activated when
PM accumulation level is "Level 1" or
"Level 2".
However, it may be activated in "Level 0"
depending on the other condition.

Important

If the regeneration remains uncompleted even
after 30 minutes have passed since the start
of automatic regeneration in PM accumulation
"Level 1", PM accumulation level enters
"Level 2".

These are the procedures of automatic
regeneration.

■

When the DPF auto regeneration inhibit

switch set to the "Auto regeneration mode":

When the conditions for automatic
regeneration are met, the automatic
regeneration starts with the regeneration
icon lighting.
When the regeneration completed, the
regeneration icon disappears.

1

65 C

55 %

2400 RPM

100 %

% SOOT

ENG RPM

FUEL LEVEL

COOL TEMP

xlfvcz-004

Automatic Regeneration_001

1

Regeneration icon

■

When the DPF auto regeneration inhibit

switch set to the "Auto regeneration inhibit
mode":

When PM accumulation level enters
"Level 1" or "Level 2", the blinking
regeneration icon appears.
Set the DPF auto regeneration inhibit
switch to the "Auto regeneration mode".

･

･

･

1.

2.

1.

2.

When the conditions for automatic
regeneration are met, the automatic
regeneration starts and the regeneration
icon changes from blinking to lighting.
When the regeneration completed, the
regeneration icon disappears.

65 C

40 %

2400 RPM

100 %

% SOOT

ENG RPM

FUEL LEVEL

COOL TEMP

1

27gtuu-008

Automatic Regeneration_002

1

Regeneration icon

3.

4.

GM2810A

Description of Functions

Page 4-32

Engine

Содержание GM2810A




























































































































































Отзывы:

Нет отзывов