Baroness GM2810A Скачать руководство пользователя страница 104

Страница: 104 / 155

Portion

No. of

Greasing

Points

Mower arm fulcrum

Lift arm fulcrum

Lift arm cylinder fulcrum

Pivot

Neutral position area

Traveling pedal shaft fulcrum

Foot brake

Pin for swiveling rear mower deck

Mower arm fulcrum
There is one greasing point on the arm
connected to each mower deck.
Grease mower decks #2 and #3 in the
swiveled position.

Mower decks #1, #4 and #5

8bq62b-025

Greasing Points_002

Mower decks #2 and #3

8bq62b-026

Greasing Points_003

Lift arm fulcrum
There is one greasing point on the arm
connected to each mower deck.
Lower the mower decks before greasing the
lift arm fulcrums.

Mower decks #1 and #4

8bq62b-225

Greasing Points_004

Mower decks #2 and #3

8bq62b-028

Greasing Points_005

Mower deck #5

8bq62b-029

Greasing Points_006

GM2810A

Maintenance

Page 6-4

Greasing

Содержание GM2810A




























































































































































Результаты поиска

Содержание GM2810A

Отзывы:

Baroness GM2810A, Руководство по эксплуатации для владельца, Страница: 104 / 155

Результаты поиска

Содержание GM2810A

Отзывы: