manualshive.com logo in svg

Baroness GM2810A, Руководство по эксплуатации для владельца, Страница: 62 / 155

Поделиться
Скачать
Baroness GM2810A Скачать руководство пользователя страница 62

Utilities

With "UTILITIES", the remaining fuel volume
can be specified and the monitor configuration
can be displayed.
The following 6 items appear when
"UTILITIES" is selected.

GAGE DATA
REMOVE ALL GAGES
SOFTWARE VERSION
FAULT CONVERSION
ANALOG INPUT
OEM

Note:
"GAGE DATA" and "REMOVE ALL GAGES"
are not supported on this machine.

Software Version

With "SOFTWARE VERSION", the software
version of the monitor can be displayed.

Fault Conversion

With "FAULT CONVERSION", the J1939
fault code conversion method can be
specified.
The monitor normally detects J1939 version
4.
Since the engine ECU of this machine uses
J1939 version 4, no adjustments are
necessary.

Analog Input

With "ANALOG INPUT", remaining fuel
volume information can be specified.
The following 2 items appear when
"ANALOG INPUT" is selected.

BACKLIGHT DIMMER
FUEL LEVEL

･
･
･
･
･
･

￭

￭

￭

･
･

Important

"BACKLIGHT DIMMER" is not supported on
this machine.
Always select "FUEL LEVEL".
If "BACKLIGHT DIMMER" is selected, "NO
DATA" appears as the value for the fuel level
parameter.

19 C

NO DATA

0 RPM

83 %

% SOOT

ENG RPM

FUEL LEVEL

COOL TEMP

cxlcph-002

Analog Input_001

Note:
The factory default analog input is "FUEL
LEVEL".

Fuel Level

With "FUEL LEVEL", the low fuel level can
be specified.

Press the menu key.
After the main menu appears, use the
arrow keys to highlight "UTILITIES", and
then press the Enter key.

3

1

2

SERVICE  REMINDERS
SELECT  UNITS
ADJUST  BACKLIGHT
ADJUST  CONTRAST

UTILITIES

3nw91f-006

Fuel Level_001

1

Menu key

2

Arrow keys

3

Enter key

1.

1.

GM2810A

Description of Functions

Page 4-26

Monitor

Содержание GM2810A




























































































































































Отзывы:

Нет отзывов