manualshive.com logo in svg

Baroness GM2810A, Руководство по эксплуатации для владельца, Страница: 118 / 155

Поделиться
Скачать
Baroness GM2810A Скачать руководство пользователя страница 118

Firmly tighten the filter cartridge by hand
until the packing contacts the mounting
surface.
And then tighten it with a half more turn.

1

ycfdh6-015

Change of Hydraulic Oil Line Filter_002

1

Filter cartridge

Supply hydraulic oil until it reaches the
specified level.
"Hydraulic Oil Supply" (Page 5-7)
Start the engine and stop it after hydraulic
oil warmed.
Check underneath the machine for
hydraulic oil leakage.
Install the filter protection plate.

Change of Hydraulic Oil Suction Filter

Caution

Be careful with hot oil, which could cause
burns if it contacts your skin.

Important

When replacing the hydraulic oil filter, be sure
to drain the oil into a container and discard it
in accordance with local laws and regulations.

Important

If the hydraulic oil emulsifies or if it becomes
even slightly less transparent, change the oil
immediately.

Important

Use Shell Tellus S2M46 (or equivalent) as
hydraulic oil.

5.

6.

7.

8.

9.

Important

Replace the intake port packing with a new
one.

On a level surface, lower the mower decks,
and then stop the engine.
Remove the left tank cover.
Remove bolts, spring washers and
washers, and then remove the intake hose
joint fitting.
Remove the old suction filter and intake
port packing.
Remove all of the old liquid gasket from the
hydraulic tank.
Remove all of the old liquid gasket and the
intake port packing from the intake hose
joint fitting.
Wash and clean the intake hose joint fitting.
Apply liquid gasket to the new intake port
packing and then install it to the intake hose
joint fitting.
Install the new suction filter to the intake
hose joint fitting.
Install the intake hose joint fitting to the
hydraulic tank.

1

6

2

3
4
5

7

6zi3qb-001

Change of Hydraulic Oil Suction Filter_001

1

Suction filter

2

Intake hose joint fitting

3

Bolt

4

Spring washer

5

Washer

6

Intake port packing

7

Hydraulic tank

Supply hydraulic oil until it reaches the
specified level.
"Hydraulic Oil Supply" (Page 5-7)
Start the engine and stop it after hydraulic
oil warmed.

1.

2.
3.

4.

5.

6.

7.
8.

9.

10.

11.

12.

GM2810A

Maintenance

Page 6-18

Adjustment and Replacement

Содержание GM2810A




























































































































































Отзывы:

Нет отзывов