![background image](http://html1.mh-extra.com/html/barco/data-708hs-r9002230/data-708hs-r9002230_owners-manual_473988048.webp)
7-10
Service Mode
5975589 BARCODATA 708 HS 080998
If a memory block adjusted on an internal # pattern is available, the
CRT run in cycle will start when pressing ENTER. If no such a block
is available, the projector cannot run the CRT run in option and leaves
the adjustment mode.
If you still want to run CRT run in cycle, create first a memory block
on an internal # pattern and restart the CRT run in option.
ENTER
starts the 'CRT run in' when an internal generated # pattern
is available.
EXIT
returns to the Path Selection main menu.
Projector Warm Up
Highlight 'Projector warm up' by pushing the control disk up or down
and press
ENTER
to select the projector warm up menu.
Select with
ê
or
é
then <ENTER>
<EXIT> to return.
COMMON SETTINGS
G2 ADJUSTMENT
CRT RUN IN CYCLE
PROJECTOR WARM UP
CRT DRIVE MODE
MEMORY BANKS
PROJECTOR WARM UP
OPTION : ON
A FULL WHITE PATTERN
WILL BE GENERATED FOR
20 MINUTES AT POWER UP
AFTER THIS PROCEDURE
THE PROJECTOR IS READY
TO PERFORM IN OPTIMUM
CONDITION
TOGGLE OPTION ON OR OFF
with <ENTER>
<EXIT> to return
The ON/OFF option can be toggled with the
ENTER
key.
When in the ON position (and the CRT run in cycle is OFF), the projector
can start up with a warm up period of 20 minutes. During the start
up a warm up menu will be displayed. This menu offers the possibility
to skip the warm up period anyway by pressing the
EXIT
key and
offers the possibility to adjust the horizontal and vertical amplitude of
this white image with the control disk. During this warm up period,
a full white image is shifted on the CRT faceplate to avoid a burn in.
Every 30 seconds a text box will be displayed on another place on
the screen with the remaining time to go.
When
EXIT
is pressed during this warm up period, the warm up menu
will be re-displayed with the remaining time indication. Press another
time
EXIT
to interrupt the warm up cycle.
When the warm up option is OFF, when switching on the projector,
it starts immediately with the projection of the selected source.
CRT Drive Mode
The projector CRT's can be driven with the normal current (normal
mode), a lower current (economic mode) or with a higher current
(boost mode).
To change the drive mode, highlight 'CRT drive mode' by pushing the
control stick forward or backward and press ENTER to display the
CRT drive mode menu.
To change the boost mode, push the control disk up or down to select
a display mode and press ENTER to select.
The following modes are available :
- Normal
- Economic : Lower drive current to the CRT's, the lifetime of the
CRT's will enlarge but the light output will reduce.
- Temporary boost : Higher drive current to the CRT's, the lifetime of
the CRT's will shorten but the light output will be higher. This situation
is temporary, when restarting the projector, the drive mode is auto-
matically set to normal.
- Permanent boost : Higher drive current to the CRT's, the lifetime of
the CRT's will shorten but the light output will be higher. This setting
will be saved in the EEPROM. When restarting the projector, it will
start up in boost mode.
COMMON SETTINGS
G2 ADJUSTMENT
CRT RUN IN CYCLE
PROJECTOR WARM UP
CRT DRIVE MODE
MEMORY BANKS
CRT DRIVE MODE
NORMAL
ECONOMIC
TEMPORARY BOOST
PERMANENT BOOST
WARNING : permanent
boost mode reduces the
lifetime
of the CRT's !
Select with
ê
or
é
then <ENTER>
<EXIT> to return.
CRT RUN IN CYCLE
A flashing white pattern will be
generated until <EXIT> is
pressed.
The projector only uses memory
blocks adjusted on an internal #
pattern; if no such block is
available, the projector can't run
the procedure and leaves the
adjustment mode.
<ENTER> to continue
<EXIT> to cancel
Содержание DATA 708HS R9002230
