Connections
2-5
5976064 BARCOCINE 8 25012000
Connecting a RGB Analog source to port 3
Connect your RGB source via an interface to Port 3.
Note :
If a line doubler or line multiplier is built in, the default position of this line doubler (multiplier) soft option is ON (active). The video input
signal will be displayed as a non interlaced image (= improved image stability).
To enable or to disable this function, enter the adjustment mode and change the position of the ON/OFF toggle switch (see chapter
'Random access' adjustment mode).
Always use an interface when a computer and local monitor have to be connected to the projector.
BARCO's Interface units.
Universal analog interface
R9826100
RGB 120 MHz Analog Interface
R9826570 (230V)
Multifunctional Analog Interface Kit
R9828120 (230V)
(MAGIK)
R9828129 (120V)
VGA interface
R9828070 (230V)
R9828079 (120V)
MAC interface
R9828050 (230V)
R9828059 (120V)
21
2))
P OWE R / MA INS
SHULSKHUDOV
5
*
% &RPS+6\QF 96\QF
COMM. PO RT
P ORT 3
PO RT 4/5
9QRP
,QRP
)UHT
6H HLQVWDOODWLRQLQV WUXFWLRQVEH IRUHFRQQHFWLQJWRWKH V XSSO\
9RLUODQRWLFHGLQVWDOODWLRQDYDQWGHUDFFRU GHU DXUpVHDX
9
$PS
+]
69,'(2
2))21
2KP
9,'(2
JUHHQRSHUDWLRQ
UHGVWDQGE\
PO RT 2
P ORT 1
2))21
2KP
P ROJECTOR MODE
7KLVGHYLFHFRPSOLHVZ LWKSD UWRI
WKH)&&UXOHV2SHUDWLRQLVVXEMHFWWR
IROORZ LQJWZ RFRQGLWLRQV 7KLV
GHYLFH PD \QRWFDXVHKDUPIXOLQWHU
IHUHQFHDQG WKLVGHYLFH PXVW
DFF HSWDQ\ LQWHUIHUHQF HUH FHLYHG
LQFOXGLQJLQWHUIHUH QFHWKDWPD \FDXVH
XQGHV LUHGRSHUDWLRQ
,1 3
,13
5
*
%
+
9
,1 387
$1$/2*,17 (5)0+]
21
2))
LQ YHU
RK P WHU P
Pin configuration D9 connector of the Analog input.
1
Not connected
2
Ground RGBS
3
RED
4
GREEN
5
BLUE
6
Ground RGBS
7
Ground RGBS
8
Hor/comp. sync
9
Vert. sync
Input selection
With the RCU or built-in RCU : press digit button 3
Connecting a RGB Analog source with composite sync to port 4/5.
RGB analog input terminals with separate H and V sync inputs, composite sync input or with sync on green. The projector detects
automatically where the sync signal is located.
Note :
If a line doubler or line multiplier is built in, the default position of this line doubler (multiplier) soft option is ON (active). The video input
signal will be displayed as a non interlaced image (= improved image stability).
To enable or to disable this function, enter the adjustment mode and change the position of the ON/OFF toggle switch (see chapter
'Random access' adjustment mode).
Always use an interface when a computer and local monitor have to be connected to the projector.
(see Connecting an Analog source to Port 3).
