Barbeques Galore G2CBL Скачать руководство пользователя страница 45

Страница: 45 / 57

Page

Troubleshooting guide

Problem

Possible Cause

Prevention / Solution

Burner will not light

No gas flow

Obstructed gas flow

Burner not over the valve

Spider webs in the burner

Burner ports blocked

Check cylinder contents- refill

Check burners and hose

Engage burner over the valve

Clean the burners

Clean the burner ports

Sudden drop in gas flow
or reduced flame height

Out of gas

Check supply / cylinder

Irregular flame pattern or
flame does not run full
length of burner

Burner ports blocked

Clean burner ports

Flame yellow or orange

Residue on burner

Spider webs in burner

Burner not over the valve

Burn clean for 10 minutes on

Clean burner

Engage the burner onto the valve

Flame blows out in wind
gusts

Too windy

Low on gas

Excess grease build up

Shelter or move the bbq

Replace or refill the cylinder

Clean the bbq

Persistent grease fire

Grease trapped by food
build-up around the burner
and grease channelling
system

Turn burners

OFF

. Turn gas

OFF

. Leave hood closed and let

the fire burn out. Once cooled,
remove and clean all parts.

Blowback (fire burning
inside the burner)

Burner and or burner tubes
may be blocked.

Switch off and re-light. If problem
persists, remove and clean the
burners.

Inside of hood peeling like
paint.

Baked on grease build up
has carbonised and is
flaking.

Clean regularly to avoid. Clean
thoroughly to resolve.

If a service is required for your barbeque, contact your
local Barbeques Galore store Phone 1 300 301 392

Содержание G2CBL


























































Результаты поиска

Содержание G2CBL

Отзывы:

Похожие инструкции для G2CBL

Бренды по названию

Популярные бренды

Barbeques Galore G2CBL, Инструкция по сборке и эксплуатации

Результаты поиска

Содержание G2CBL

Отзывы:

Похожие инструкции для G2CBL

Бренды по названию

Популярные бренды