background image

Page 

44 

Care and maintenance (continued) 

 

Storing Your Barbeque: 

Your barbeque is designed to be used outdoors. However, just like a car, you will prolong the life 
of the appliance if you store it out of direct exposure to the elements when not in use. This can be 
done in many ways: 

  Place a waterproof cover over it. These are available from most barbeque retailers. Use a 

ventilated cover, or add a couple of sponges between the cover and the barbeque to promote 
ventilation and reduce condensation. 

  Move the barbeque to a covered location. If you are storing it in a closed room (e.g. a shed or a 

garage) then disconnect and keep the cylinder outdoors and away from any other cylinders or 
any cars, boats, motorcycles or any other petrol engines. 

 

If you don’t intend to use it for a few months, lightly spray all surfaces with canola oil. This will 
help protect against corrosion. 

 

Servicing Your Barbeque: 

  Apart from cleaning, your barbeque is a fairly low maintenance item. A couple of things are 

worth looking at though. Remember to turn off and disconnect the gas before any maintenance 
is carried out. 

  If your barbeque uses a flexible hose to connect to the gas, check the rubber O-ring on the 

regulator end of the hose assembly at least once a year. If it appears worn or cracked, have it 
replaced. 

  We recommend having your barbeque checked by an authorised service agent every 5 years. 

This is to ensure there are no leaks and that all components are still functioning correctly. 

   If you use a portable LPG gas cylinder, you will need to have the cylinder serviced or replaced 

every ten years. The date of the last service should be stamped on the neck of the bottle. 

 

As you can see, it’s easy to keep your barbeque in great shape so it can give you years of 
trouble free enjoyment. 

 

Replacing the hose: 

If there are any signs of wear or cracking in the barbeque hose(s), you need to replace them 
immediately. Ensure you replace only with the correct hose and regulator purchased from 
Barbeques Galore to ensure proper gas connection compatibility. 
Connect the nut of the hose to the same gas inlet of the barbeque that the old one was connected. 
Use two spanners to tighten it properly, one to hold the inlet, one to turn the hose nut. Do not use 
sealing tape. The connection is designed to seal properly without it. Perform a leak test as 
explained in the installation section before use. 
 

Replacing the burners: 

Occasionally you will need to remove your burners for cleaning or adjustment. 

 

To replace the burner, place the open end of the burner over the gas jet at the front of the 
barbeque. Then, lower the lug on the other end of the barbeque into the locating hole. 

 

 

 

 

 

 

Содержание G2CBL


























































Отзывы: