background image

30

DISmANTLING AND DISPOSAL

Only qualified persons must be allowed to dismantle the pump and this operation must be performed in 

compliance with the laws applicable in the country where the machine in which it is integrated has been installed.

TROUbLESHOOTING

 WARNING

• Also follow the instructions contained in the manual of the machine in which the pump is integrated.

• Before doing any jobs, perform the operations described in the 

“s

top

 paragraph.

  In the event of not being able to restore the correct operation of the pump with the aid of the information 

contained on the following table, contact a 

Skilled Technician

.

PRObLEmS

CAUSES

REmEDIES

The pump does not 

prime.

Suction of air.

Check the integrity of the suction circuit.

Delivery line closed (e.g., spray gun closed).

Reset the delivery pressure (e.g., press the spray 

gun lever).

Suction circuit with choke points.

Check the suction circuit (especially make sure 

the suction filter is clean).

The pump fails to reach 

max pressure.

Pressure adjustment knob (15) not tightened 

enough.

Turn the knob clockwise until required pressure 

is achieved.

Not enough water supply or priming too deep. Make sure the water supply flow rate or priming 

depth is in compliance with the indications in the

 

“S

PECIFICATIONS

 

AND

 

TECHNICAL

 

DATA

 paragraph.

Suction circuit with choke points.

Check the suction circuit (especially make sure 

the suction filter is clean).

Unsuitable conditions of use (e.g., nozzle worn, 

lance in low-pressure position, etc.)

Restore the correct conditions of use.

Irregular pressure and 

flow rate (pulsating).

Air suction.

Check the integrity of the suction circuit.

Suction filter dirty.

Clean the filter.

Not enough water supply or priming too deep. Make sure the water supply flow rate or priming 

depth is in compliance with the indications in the

 

“S

PECIFICATIONS

 

AND

 

TECHNICAL

 

DATA

 paragraph.

The pump has not completed priming.

Prime the pump according to the indications 

of the 

“S

TANDARD

 O

PERATION

 (

HIGH

 

PRESSURE

)”

 

paragraph.

Accessory clogged (e.g. clogged nozzle).

Restore the correct use of the accessory.

Too much noise.

Suction circuit with choke points.

Check the suction circuit (especially make sure 

the suction filter is clean).

Water supply temperature too high.

Keep to the temperatures indicated in the 

“S

PECIFICATIONS

 

AND

 

TECHNICAL

 

DATA

 paragraph.

Low detergent suction. Use of the accessory not in low-pressure mode 

(e.g., lance not in low-pressure position).

Restore the correct use of the accessory.

Detergent metering device closed or set for 

low suction.

Turn the detergent adjustment knob (16) 

anticlockwise.

Use of detergent which is too viscous.

Keep to uses and dilutions shown on detergent 

plate.

Содержание Comet AX Series





















Отзывы: