Banner Q4X Series Скачать руководство пользователя | Manualshive

Страница: 6 / 46

background image

2 Installation

2.1 Install the Safety Label

The safety label must be installed on Q4X sensors that are used in the United
States.

Note:

Position the label on the cable in a location that has

minimal chemical exposure.

1. Remove the protective cover from the adhesive on the label.
2. Wrap the label around the Q4X cable, as shown.
3. Press the two halves of the label together.

COMPLIES WITH IEC 60825-1:2007

CLASS 1

LASER PRODUCT

COMPLIES WITH 21 CFR 1040.10 AND 1040.11
EXCEPT FOR DEVIATIONS PURSUANT TO
LASER NOTICE No. 50, DATED JUNE 24, 2007.
BANNER ENGINEERING CORP.
9714 10TH AVENUE NORTH
MINNEAPOLIS, MN 55441

COMPLIES WITH

IEC 60825-1:2007

CLASS

1

LASER PRODUCT

Figure 4. Safety Label Installation

2.2 Sensor Orientation

Optimize detection reliability and minimum object separation performance with correct sensor-to-target orientation. To ensure
reliable detection, orient the sensor as shown in relation to the target to be detected.

Figure 5. Optimal Orientation of Target to Sensor

See the following

figures

for examples of correct and incorrect sensor-to-target orientation as certain placements may pose

problems for sensing some targets. The Q4X can be used in the less preferred orientation and provide reliable detection
performance; refer to the

Performance Curves

for the minimum object separation distance required for each case.

Incorrect

Correct

Figure 6. Orientation by a wall

Incorrect

Correct

Figure 7. Orientation for a turning object

Incorrect

Correct

Figure 8. Orientation for a height difference

Horizontal

Orientation

Vertical

Orientation

(Optimal)

Figure 9. Orientation for a color or luster difference

2.3 Mount the Sensor

1. If a bracket is needed, mount the sensor onto the bracket.
2. Mount the sensor (or the sensor and the bracket) to the machine or equipment at the desired location. Do not tighten the

mounting screws at this time.

Q4X Stainless Steel Laser Sensor with Dual Discrete Outputs and IO-Link

6

www.bannerengineering.com - Tel: 763.544.3164

«
...
4
5
6
7
8
...
»

Содержание Q4X Series















































Отзывы:

Нет отзывов

Похожие инструкции для Q4X Series

Бренд: Banner Страницы: 2

Бренд: Cane Creek Страницы: 2

Бренд: Calsense Страницы: 6

Бренд: LAZER Страницы: 6

Бренд: ICON Страницы: 8

Бренд: oliser Страницы: 6

Бренд: Vaillant Страницы: 80

Бренд: Panasonic Страницы: 242

Бренд: Broil King Страницы: 2

Бренд: Olympus Страницы: 42

Бренд: Accessory Power Страницы: 7

Бренд: B-PWR Страницы: 13

Бренд: N-Com Страницы: 6

UpFront STS 12 Combo

Бренд: Hagie Страницы: 149

Бренд: N-Com Страницы: 2

Бренд: Barazza Страницы: 4

Бренд: IFM Страницы: 5

Бренд: walimex Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды