Banner Q4X Series Скачать руководство пользователя

Страница: 10 / 46

Two-Point Static Teach
Dynamic Teach

Background Suppression

Foreground Suppression

Top Menu

Sub Menu

off: no delays enabled
on: enable on and/or off delay (set value in Delay Timer menu)
1 Shot, fixed output pulse duration
Total

end: exit setup

Teach Selection CH2

Output CH2

Window Size CH2 **

Output Timing Delays CH2

Offset CH2 ****

Exit Setup

( default setting)

Light Operate

Dark Operate

Complimentary to Output 2

Dual Mode

Adaptive Tracking CH2 *

off: Adaptive Tracking off
High-Speed Adaptive Tracking on

on: Adaptive Tracking on

Channel 2

Adaptive Tracking menu is available when Teach CH2 is set to Dual Mode

laser off when pulled high

laser on when pulled high

set: Remote Teach input

master

slave

pulse

sec range, set Delay Timer value (seconds have decimal)

Menu not present when is set to
( and default to 0, defaults to 1 or 10 depending on response speed setting)

Delay Timer CH2 ***

Available when

set to

Available when

set to

available when

set to

Menu items only available when
out2 is set to LO or DO

Auto

Set Value:

Offset menu is available when Teach CH2 is set to FGS or BGS

-75 to 75 for 100/110 mm models

-275 to 275 for 300/310 mm models

-575 to 575 for 600/610 mm models

0.2 to x, where x depends on measuring span:

Window Size menu is available when Teach CH2 is set to FGS

75 for 100/110 mm models

275 for 300/310 mm models

575 for 600/610 mm models

Figure 13. Sensor Menu Map—Channel 2

3.2.1 Output

Note:

The number that follows

out

on the display indicates which channel is selected.

The Output 1 menu is available in Channel 1. Use this menu to select light operate (LO) or dark operate (DO). The default output

configuration

is light operate. To switch between light operate and dark operate, select the desired menu option.

•

—Light operate

•

—Dark operate

The Output 2 menu is available in Channel 2. Use this menu to set the output

configuration

for Channel 2. The default is light

operate.

•

—Light operate

•

—Dark operate

Q4X Stainless Steel Laser Sensor with Dual Discrete Outputs and IO-Link

www.bannerengineering.com - Tel: 763.544.3164

Содержание Q4X Series















































Результаты поиска

Содержание Q4X Series

Отзывы:

Похожие инструкции для Q4X Series

Бренды по названию

Популярные бренды

Banner Q4X Series, Инструкция по эксплуатации

Результаты поиска

Содержание Q4X Series

Отзывы:

Похожие инструкции для Q4X Series

Бренды по названию

Популярные бренды