manualshive.com logo in svg

Banner Q4X Series, Инструкция по эксплуатации

Поделиться
Скачать
Banner Q4X Series Скачать руководство пользователя страница 23

Switch 

Point 

Value A

Switch 

Point 

Value -A

2

Press and Hold 

 > 2s

1

3

Press again

Figure 19. One-Point Window (Foreground Suppression)

In order to reliably detect changes from the taught background, if multiple laser 

reflections

 are returning to the sensor, the output

status is treated as though the target is outside of the taught window. The display alternates between 

 and the measured

distance. Realign the laser to avoid light 

reflecting

 off of multiple targets if this extra level of 

verification

 is not desired.

Note: 

The sensor must be set to 

 = 

 to use the following instructions. The FGS indicator is amber to

indicate One-Point Window (Foreground Suppression) mode.

Note: 

To program the sensor using remote input, remote input must be enabled (

 = 

).

1. Present the target.

Method

Action

Result

Push Button

Present the target. The sensor-to-target distance must be within the
sensor's range.

The target's measurement value
displays.

Remote Input

2. Start the TEACH mode.

Method

Action

Result

Push Button

Press and hold 

TEACH

 for longer than 2 seconds.

Light Operate

 and 

 

flash

 alternately

on the display. The FGS indicator

flashes.

Dark Operate

 and 

 

flash

 alternately

on the display. The FGS indicator

flashes.

Remote Input

No action required.

N/A

3. Teach the sensor.

Method

Action

Result

Push Button

Press 

TEACH

 to teach the target.

The ± window size 

flashes

 rapidly and

the sensor returns to Run mode.

Remote Input

Single-pulse the remote input.

T

Table 5: Expected TEACH Behavior for One-Point Window (Foreground Suppression)

See 

Figure 23 

on page 34 for the minimum object separation.

 

 

Q4X Stainless Steel Laser Sensor with Dual Discrete Outputs and IO-Link

 

www.bannerengineering.com - Tel: 763.544.3164

23

Содержание Q4X Series















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды