background image

23

S

B

I M P LY

E T T E R !

B K

&

RS-232 Command and Control

An HD6 may be controlled externally using the rear panel RS-232 I/O RJ-45 connector. An external control
system may be directly connected to the HD6 to control either the HD6 or both HD6 and a CT Receiver. For use
in an external RS-232 automation control system, the control device must connect to the RS-232 I/O RJ-45
connector on the back of the HD6. A distilled list of RS-232 commands for use with a default HD6 system setup
is provided on the following pages. 

Note: For use with an HD6 Linked to a CT Series Receiver, the external control device must treat the linked pair
as a single CT Receiver device. All RS-232 control shall use the appropriate CT Receiver BKC-DIP commands.
This applies regardless of the fact that the RS-232 control system is connected to the HD6 RS-232 I/O
connector. All BKC-DIP commands shall pass through the HD6 to the linked CT Receiver. The Linked CT
Receiver handles all control of the HD6 through the CT RS-232 Link cable. Complete HD6 BKC-DIP informa-
tion may be found in the HD6 product appendices. 

HD6 BKC-DIP (Abbreviated List) 

Shown with default settings: Transmit ID = 00, Receive ID = 00, Zone A = code-set 11, Zone B = code-set 12,etc.

Power Commands

On, Off and Toggle

(00, S, I, 0B=40;)

Power On Zone 11

(00, S, I, 0E=40;) 

Power On Zone 14

(00, S, I, 0C=40;)

Power On Zone 12

(00, S, I, 0F=40;) 

Power On Zone 15

(00, S, I, 0D=40;)

Power On Zone 13

(00, S, I, 10=40;)

Power On Zone 16

(00, S, I, 00=40;)

Power On Zone 0 (WHOLE-HOUSE)

(00, S, I, 0B=80;)

Power Off Zone 11

(00, S, I, 0E=80;) 

Power Off Zone 14

(00, S, I, 0C=80;)

Power Off Zone 12

(00, S, I, 0F=80;) 

Power Off Zone 15

(00, S, I, 0D=80;)

Power Off Zone 13

(00, S, I, 10=80;) 

Power Off Zone 16

(00, S, I, 00=80;)

Power Off Zone 0 (WHOLE-HOUSE)

(00, S, I, 0B=45;)

Power Toggle Zone 11

(00, S, I, 0E=45;)

Power Toggle Zone 14

(00, S, I, 0C=45;)

Power Toggle Zone 12

(00, S, I, 0F=45;)

Power Toggle Zone 15

(00, S, I, 0D=45;)

Power Toggle Zone 13

(00, S, I, 10=45;)

Power Toggle Zone 16

(00, S, I, 00=45;)

Power Toggle Zone 0 (WHOLE-HOUSE)

Input Select Commands

ZONE A

(code-set 11)

(00, S, I, 0B=A0;)

Select IN 1 for Zone 11

(00, S, I, 0B=52;) 

Select IN 6 for Zone 11

(00, S, I, 0B=90;)

Select IN 2 for Zone 11

(00, S, I, 0B=D0;) 

Select IN 7 for Zone 11

(00, S, I, 0B=60;)

Select IN 3 for Zone 11

(00, S, I, 0B=E0;)

Select IN 8 for Zone 11 

(00, S, I, 0B=B0;)

Select IN 4 for Zone 11

(00, S, I, 0B=76;)

Select IN 9 for Zone 11

(00, S, I, 0B=F0;)

Select IN 5 for Zone 11

(00, S, I, 0B=5A;)

Select D-IN for Zone 11

ZONE B 

(code-set 12)

(00, S, I, 0C=A0;)

Select IN 1 for Zone 12      (00, S, I, 0C=52;) 

Select IN 6 for Zone 12

(00, S, I, 0C=90;)

Select IN 2 for Zone 12      (00, S, I, 0C=D0;)  

Select IN 7 for Zone 12

(00, S, I, 0C=60;)

Select IN 3 for Zone 12      (00, S, I, 0C=E0;) 

Select IN 8 for Zone 12

(00, S, I, 0C=B0;)

Select IN 4 for Zone 12

(00, S, I, 0C=76;) 

Select IN 9 for Zone 12

(00, S, I, 0C=F0;)

Select IN 5 for Zone 12     (00, S, I, 0C=5A;)

Select D-IN for Zone 12

SERIAL CONTROL COMMANDS

Содержание HD6





























Отзывы: