manualshive.com logo in svg

Balboa TP200 PANEL, Руководство пользователя

Поделиться
Скачать
Balboa TP200 PANEL Скачать руководство пользователя страница 28

SUCCESSFUL TEST

The spa will power 
Off if the GFCI test is 
successful. Power On 
the spa at the GFCI.

UNSUCCESSFUL TEST

This indicates that the test has failed.
When this message appears, the spa 
will be inoperable, and the spa should 
be powered Off. A spa technician 
needs to fix the electrical problem.

TP200 

USER GUIDE   

     

42369 Rev A2

52

51

Balboa Water Group   |   Your Single Source Solution

A GFCI is an important 
safety device and is 
required equipment on 
a hot tub installation.

Your spa may be equipped with a GFCI 
Protection feature. (UL rated systems only.) 
If your spa has this feature enabled by the 
manufacturer, the GFCI Trip Test must occur 
to allow proper spa function.

Within 1 to 7 days after startup, the spa may 
trip the GFCI to test it. (The number of days 
is factory programmed.) The GFCI must be 
reset once it has tripped. After passing the 
GFCI Trip Test, any subsequent GFCI trips 
will indicate a ground fault or other unsafe 
condition and the power to the spa must be 
shut off until a service person can correct the 
problem.

Not all control systems trip the GFCI 
automatically after a certain number of days. 
If the control system does not trip the GFCI 
automatically, the GFCI must be tripped 
manually. 

Forcing the GFCI Trip Test

The installer or spa owner can cause the 
GFCI Trip Test to occur at any time by 
following the sequence on the next page.
The GFCI should trip within a few seconds 
and the spa power should shut down. If the 
GFCI does not trip (see next page), shut 
down the power to the spa.
The installer or service technician should:  
•  Manually verify that a GFCI breaker is    
  installed and that the circuit and spa are  
  wired correctly. 
•  Verify the function of the GFCI with its own  
  test button. 
•  Restore power to the spa and repeat the  
  GFCI Trip Test.
Once the GFCI is tripped by the test, reset 
the GFCI and the spa will operate normally 
from that point. You can verify a successful 
test by following the sequence on page 54. 
PASS should appear after a temp button is 
pressed from the GFCI screen. 

The end user should always be 
trained to test and reset the GFCI on 
a regular basis.

WARNING:

If freezing conditions exist, a GFCI should be 
reset immediately or spa damage could result. If 
the GFCI does not reset and freezing conditions 
exist, drain the spa of all water until the spa is 
functional again. 

SEQUENCE - TEST THE GFCI

Press the TEMP button. The Set 
Temperature will appear and flash.

While the Set Temperature is flashing,  
press LIGHT until UTIL appears. 

This indicates that you are entering 
GFCI Test Mode.  (

This feature is not 

available on CE rated systems.

)

This screen will display either  
ARMD or PASS.

Press TEMP and TRIP will  
begin flashing.

Press TEMP to perform the test.

Main Screen

Follow this sequence to perform a GFCI test. 

If the test is successful, the spa will power Off. 

If the test is unsuccessful, the spa needs to be 
powered Off, and a spa technician needs to 
fix the electrical problem.

The GFCI test feature is not available 
on CE rated control systems.

Flashing characters

Progressive message

Press TEMP button for “action”

Press LIGHT button to “select”

Pause / back to Main Screen / setting not saved

Pause / back to Main Screen / setting saved

           Menu Items may or may not appear

SEQUENCE KEY  

( View page 2 for full description )

 UTILITIES

GFCI TEST FEATURE

Содержание TP200 PANEL


































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды