manualshive.com logo in svg

Balboa TP200 PANEL, Руководство пользователя

Поделиться
Скачать
Balboa TP200 PANEL Скачать руководство пользователя страница 21

TP200 

USER GUIDE   

     

42369 Rev A2

38

37

Balboa Water Group   |   Your Single Source Solution

Check the ozone and/or UV generator. 

This message may appear every 360 days. 
Check your ozone and/or UV generator per 
your spa manufacturer’s instructions.

Treat the wood. 

This message may appear every 180 days. 
Wood skirting and furniture should be cleaned 
and conditioned per the manufacturers 
instructions for maximum life.

Change the water filter. 

This message may appear every 360 days. 
Filters should be replaced occasionally to 
maintain proper spa function and  
sanitary conditions.

Change the spa water. 

This message may appear every 90 days. 
Change the water in the spa on regular 
basis to maintain proper chemical balance 
and sanitary conditions.

Clean the spa cover. 

This message may appear every 180 
days. Vinyl covers should be cleaned and 
conditioned for maximum life.

Change the mineral cartridge  
as needed. 

Install a new mineral cartridge per you spa 
manufacturer’s instructions.

Test the GFCI or RCD. 

This message may appear every 30 days. The 
Ground Fault Circuit Interrupter (GFCI) or 
Residual Current Device (RCD) is an important 
safety device and must be tested on a regular 
basis to verify its reliability.
Every user should be trained to safely test  
the GFCI or RCD associated with the  
hot tub installation.
A GFCI or RCD will have a TEST and  
RESET button on it that allows a user to verify 
proper function. 

Warning:

If freezing conditions exist, a GFCI or RCD 
should be reset immediately or spa damage 
could result. If the GFCI or RCD does not reset 
and freezing conditions exist, drain the spa of 
all water until the spa is functional again.  
The end user should always trained to test and 
reset the GFCI or RCD on a regular basis.

Your spa needs a service check. 

This message may appear every 365 days. 
Contact your service organization for a  
service check.

Содержание TP200 PANEL


































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды