BACA SYSTEMS EDGE XL Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 52

background image

8/15/2019

28

5.

The 3 buttons below operate the laser:

a.

The laser button on the left is used to calibrate the laser. Place the laser reflectors
in the table before clicking this button. Then watch the laser scan the reflectors.
Make sure all 4 reflectors are scanned. If all 4 reflectors are not scanned, check to
make sure the reflectors are clean.

b.

The laser button in the middle will display the vacuum pods on the table.

c.

The laser button on the right will display the pieces on the table.

6.

The speed of the machine can be controlled using either the -/+ keys, the slider bar, or
by clicking on the number you can type in a new number. The number represents
federate percentage. The example below show 100% federate.

7.

The

START

button will start the program, as long as the machine is in automatic mode.

8.

The

STOP

button will pause the program from running.

«
...
26
27
28
29
30
...
»

Содержание EDGE XL





















































Отзывы:

Нет отзывов

Похожие инструкции для EDGE XL

Бренд: Jafar Страницы: 10

Бренд: Jafar Страницы: 8

Бренд: CAME Страницы: 12

Бренд: CAME Страницы: 16

Бренд: Ultrak Страницы: 41

Бренд: Zander Aachen Страницы: 10

ElectraElite IPK

Бренд: NEC Страницы: 20

Бренд: B meters Страницы: 2

Бренд: Salda Страницы: 16

Бренд: Gate Motors Страницы: 6

Бренд: HAMTRONICS Страницы: 8

Бренд: Neets Страницы: 12

Бренд: National Instruments Страницы: 24

Бренд: Panamax Страницы: 16

EP Series Pro-Bloc

Бренд: Parker Страницы: 11

Бренд: Parker Страницы: 22

Бренд: Parker Страницы: 2

JetWeb JX2-PRN1

Бренд: Jetter Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды