BACA SYSTEMS EDGE XL Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 52

background image

8/15/2019

15

8.

The

FILENAME

,

STANDARD

, and

REAL

buttons are used to change how the icons are

displayed. Click the button to toggle between each mode.

9.

The

DELETE

button with the trash can icon is used to delete all clamps. It will appear

when no clamps are selected. The

DELETE

button with the red X is used to delete only

selected clamps. It will appear when at least one clamp is selected.

10.

The

STOP

button with the red arrows is used to automatically move a selected stop in

the workspace up to the edge of the nearest piece.

11.

The

FLOOD

button makes the pieces appear as a solid color or transparent. If the button

is yellow, it means the flood is on and the pieces will display as a solid color.

«
...
13
14
15
16
17
...
»

Содержание EDGE XL





















































Отзывы:

Нет отзывов

Похожие инструкции для EDGE XL

Бренд: Parker Страницы: 30

Бренд: VAT Страницы: 22

Бренд: GARDTEC Страницы: 48

Бренд: FAAC Страницы: 64

Бренд: jbc Страницы: 4

Бренд: Eaton Страницы: 86

Бренд: TAC Страницы: 4

Бренд: ZETRON Страницы: 3

Бренд: Abicor Binzel Страницы: 8

Бренд: Danfoss Страницы: 7

Бренд: Saga Страницы: 9

Бренд: Jabra Страницы: 4

Бренд: Lamtec Страницы: 136

Бренд: National Instruments Страницы: 8

Бренд: u-blox Страницы: 28

Бренд: U-Prox Страницы: 3

Бренд: L-Acoustics Страницы: 20

Бренд: Voltech Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды