BACA SYSTEMS EDGE XL Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 52

background image

8/15/2019

26

PROJECTS

1.

Click

PROJECTS

.

The

PROJECTS

menu is used to save the current project, open saved projects, and delete

items from the workspace.

2.

The

FILE

button will list all the saved projects to open.

3.

The

SAVE

button allows you to save a copy of the workspace.

4.

The

CUTS

button will remove all machinings from the workspace.

5.

The

PIECES

button will remove all pieces from the workspace.

6.

The

ALL

and

QUANTITA

buttons will remove everything from the workspace.

«
...
24
25
26
27
28
...
»

Содержание EDGE XL





















































Отзывы:

Нет отзывов

Похожие инструкции для EDGE XL

615 Series ANSI

Бренд: ABB Страницы: 60

Бренд: Nelsen Corporation Страницы: 16

Бренд: National Instruments Страницы: 8

Бренд: National Instruments Страницы: 34

Бренд: ZIMO Страницы: 38

C-NaviGator III

Бренд: C-Nav Страницы: 20

Бренд: Ebyte Страницы: 38

Бренд: EBS Страницы: 30

Бренд: Madas Страницы: 6

Бренд: Madas Страницы: 11

Бренд: Parkside Страницы: 65

Бренд: Rane Страницы: 2

Бренд: UNICORECOMM Страницы: 32

Бренд: UNICORECOMM Страницы: 7

Бренд: UNICORECOMM Страницы: 26

Бренд: UNICORECOMM Страницы: 25

Бренд: Union Instruments Страницы: 63

Бренд: Ultraflex Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды