Baby Lock Pro Line BL4-838D Скачать руководство пользователя страница 35

Страница: 35 / 36

19 SPECIFICATION

Item Specification

Stitch width (standard)
Stitch width (narrow rolled edging)
Stitch length
Number of threads
Needle
Maximum sewing speed
Machine weight
Lamp

3.5 ~ 7.5 mm
1.5 mm (M)
1 ~ 4 mm
4, 3 or 2 thread
DC x 1F #11 or # 14
1500 rpm
7.5 kg (with motor)
15W/110V
10W/240V (over 200 voltage country)

20 DO’S AND DON’TS

1. Always be aware of the up – and – down movement of the needle and do not turn your attention

from the machine while it is running.

2. When changing the needle, the presser foot, or any other parts, always disconnect the machine by

turning the power switch to “off”.

3. Do not place anything on the speed controller, otherwise the machine will start inadvertently, or the

controller or motor may burn out.

4. The maximum permissible power for the sewing lamp bulb 10 ~ 15 watts 110 volts or 15 watts 240

volts (over 200 voltage country).

5. When using your serger for the first time, place a piece of waste fabric under the presser foot and

run the machine without thread for a few minutes. Wipe away any oil which may have appeared.

6. Do not pull fabric from rear of machine, this may damage looper mechanism.

7. To prevent possible injury, always avoid body contact with any moving parts and machine

mechanism.

Special Caution: Unplug the power cord from the power source when the machine is not in use.

Downloaded from www.Manualsoncd.com

Содержание Pro Line BL4-838D





































Результаты поиска

Содержание Pro Line BL4-838D

Отзывы:

Похожие инструкции для Pro Line BL4-838D

Бренды по названию

Популярные бренды

Baby Lock Pro Line BL4-838D, Инструкция

Результаты поиска

Содержание Pro Line BL4-838D

Отзывы:

Похожие инструкции для Pro Line BL4-838D

Бренды по названию

Популярные бренды