Baby Lock Kinetic Frame Скачать руководство пользователя страница 26

Страница: 26 / 28

26 Baby Lock Kinetic Frame Assembly Instructions

Step 13: Pole to Frame Assembly

Parts needed

(1) frame assembly

(1) batting storage pole

(1) quilt-top pole

(1) backing pole

(1) take-up pole

13-1: Place the poles on the frame as shown in

Fig. 13-1. The poles will snap past the plastic

fingers, which are shown in Detail 8-2a.

Step 14: Rubber End Cap Assembly

Parts needed

(1) frame assembly with poles

(8) rubber end caps

14-1: Slide one (1) rubber end cap onto

the end of each bolt sticking out of the pole

ends, as shown in Fig. 14-1. If the poles

are assembled properly, there should be

approximately 3/8-inch to ½-inch of metal

threads showing beyond the ends of the pole.

Fig. 14-1

Steps 13 & 14

Pole to Frame Assembly

Rubber End Cap Assembly

Rubber End Cap

Fig. 13-1

Take-Up Pole

Backing Pole

Batting Storage Pole

Quilt-Top Pole

Idler Pole

Содержание Kinetic Frame





























Результаты поиска

Содержание Kinetic Frame

Отзывы:

Похожие инструкции для Kinetic Frame

Бренды по названию

Популярные бренды

Baby Lock Kinetic Frame, Руководство по сборке

Результаты поиска

Содержание Kinetic Frame

Отзывы:

Похожие инструкции для Kinetic Frame

Бренды по названию

Популярные бренды