Ayrton wildsun k25, Руководство пользователя

Страница: 8 / 18

USER MANUAL _
8
DMX512 CONNECTION WITH TERMINATION PLUG
For installations where the DMX cable must extend over long distances,
or if it is located near areas with major electrical disturbance, it is
recommended to use a DMX termination plug. This helps prevent
luminaires from malfunctioning due to interference. The DMX termination
plug, composed simply of a male XLR input connector with a 120-Ohm
resistor, is soldered between pins 2 and 3. This plug must be connected to
the DMX output of the last luminaire in the chain.
Refer to the following diagram:
SING DMX VIA ART-NET
To control the WILDSUN K25 via ART-NET, the fixtures must be
interconnected with CAT5 RJ45 cable. Be careful to enter all necessary
information into the ART-NET universe being used and specify in the menu
that the WILDSUN K25 is being controlled through ART-NET (see OPTION
DETAILS in the « OPTIONS » menu).
WARNING!
THE WILDSUN K25 CAN ONLY READ THE FIRST TWENTY FOUR
UNIVERSES OF AN ART-NET PACKAGE. IF YOU HAVE MORE THAN 24
UNIVERSES IN YOUR NETWORK, YOU MUST USE A CONFIGURABLE
SWITCH TO FILTER EACH RJ45 OUTPUT.
THE WILDSUN K25 DMX ADDRESS SETTING
All luminaires have a DMX start address correctly set when using a DMX
signal to control them. The DMX start address is the channel from which
the luminaire “listens” to the digital control information sent by the DMX
controller.
The start address must conform to the one recorded on the DMX controller
to run the luminaire. This address is the DMX value that appears on the
luminaire’s display. You can set the same address for all the luminaires, or
some of them, but you can also set a different address for each luminaire,
as needed.
If you do set the same address for all the luminaires, they will all “listen”
from the DMX channel you have set. The instructions sent by the DMX
controller will affect all luminaires at the same time. If you set a different
address per luminaire, the DMX controller can control each independently.
If, for instance, the fixtures are preset in 21-channel DMX mode (required
for full control), you will need to adjust the DMX address for the luminaires
as follows: The first unit with DMX address 001, the second with DMX
address 022 (21 + 1), the third with DMX address 043 (21 + 22), etc.
CONTROL PANEL (MENU OPTIONS)
A large number of settings are accessible from the fixture’s control panel.
A good working knowledge of it will enhance the fixture’s possibilities.
You can access the Main Menu by pressing the key until the display
flashes.
Cycling through the menus is performed by pressing the , ,
or keys, as required:
Press the key to select the desired menu.
Change the selection by pressing the , or , keys.
Confirm your selection by pressing the key.
Exit a menu at any time by pressing the key.
Notes:
You can return to the display by pressing the
or keys from the
basic display.
If the screen fails to respond, hold the “Mode Esc” key down for at least 3
seconds to free up the display.
The fixture’s menu functions are described in the following table:
Address Set Dmx Addr A001~AXXX DMX address setting
Mode
User Mode Stand Mode
Basic Mode
Extend Mode
User Mode A
User Mode B
User Mode C User’s mode to change
channel numbers
Edit User Max channel
PAN
: Edit DMX profile
Options
Status No DMX Mode
Pan Reverse
Tilt Reverse
Pan Degree
Feedback
Pan/Tilt Spd
Hibernation Close/Hold/Auto/Music
ON/OFF
ON/OFF
630/540
ON/OFF
Speed 1~ 4
OFF, 01min > 99min Auto run if no DMX
Pan Reverse movement
Tilt Reverse movement
Pan Degree Select
Movement Feedback
Reset Pan/Tilt
Stand by Mode
Service PIN Service PIN
RDM PID
Set IP Password=XXX
xxxxxx
xxx.xxx.xxx.xxx Service Password“=050”
RDM PID Code
IP Addr
Fans Control Auto
Stage
Studio Head Fans Speed Mode
Select
Disp.Setting Shutoff Time
Flip Display
Key Lock
Disp Flash 02~60m 05m
ON/OFF
ON/OFF
ON/OFF Display shutoff time
Reverse 180 degree
Key Lock
No Signal Flash
Signal Select DMX
WDMX
ArtNet
sACN DMX
Wireless DMX
Art-Net
sACN
Set Universe xx Art-Net Universe NO.
Temp. C/F
Celsius
Fahrenheit
Temperature switch
between °C/°F
Initial Pos. PAN =XXX Initial effect position
Wireless DMX Activate WDMX
Act&Data Out
Rest WDMX Activate WDMX
Activate & Data Out
Reset Wireless DMX Mem
Trigger DMX Value Disp.
Set To Slave
Auto Program PAN, TILT etc.
Slave1,Slave2,Slave3
Master / Alone DMX value display
Slave setting
Auto program
Reset Default ON/OFF Restore factory sett.
Info
Time Info. Current Time
Ttl Life Hrs
Last Run Hrs
Timer PIN
Clr Last Run XXXX(Hours)
XXXX(Hours)
XXXX(Hours)
Password=XXX
ON/OFF
Temp. Info Head Temp. XXX °C/°F
Software Ver V1.0… Software version
Network IP,Mask,Mac Network setting