Avitel 5303 Скачать руководство пользователя | Manualshive

Страница: 33 / 64

background image

33

© 2008 Directed Electronics. All rights reserved.

Programming jumpers

➤

Tach threshold On/Off

In most cases, this jumper can be left in the Off position. Some new vehicles use

less than 12 volts in their ignition systems. The unit may have trouble learning the

tach signal in these vehicles. Changing the jumper to the On setting changes

the trigger threshold of the digital tach circuit so that it will work with these type

vehicles.

➤

Light flash (+) / (-) polarity

The internal fuse is used to determine the light flash output. In the (+) position, the

onboard relay will output (+)12V on the WHITE wire, H1/11. In the (-) position,

the on-board relay will supply a (-) output When wiring into a multiplex circuit,

you can replace the fuse with a resistor (paying attention to the polarity setting).

(Refer to diagram on p.24, H1/4 White/ Brown wire description).

Note:

For parking light circuits that draw 10 amps or more, the internal jumper

must be switched to a (-) light flash output. P/N 8617 or a standard automotive

SPDT relay must be used on the H1/11 light flash output harness wire.

��

��

��

��

��

��

��

��

��

��

«
...
31
32
33
34
35
...
»

Содержание 5303

































































Отзывы:

Нет отзывов

Похожие инструкции для 5303

Бренд: La Crosse Technology Страницы: 10

Бренд: Tanda Страницы: 9

Бренд: NATURE & DECOUVERTES Страницы: 9

Бренд: ELRO Страницы: 2

Бренд: REV Ritter Страницы: 10

Бренд: Geemarc Страницы: 32

Бренд: Sony Страницы: 2

DREAM MACHINE ICF-C430

Бренд: Sony Страницы: 16

Бренд: Universal Страницы: 8

Бренд: RED Страницы: 2

Бренд: Oregon Scientific Страницы: 12

Бренд: HMC Страницы: 23

Бренд: EVERSPRING Страницы: 5

Бренд: Equity Страницы: 4

NIGHT VISION 30330B

Бренд: Equity Страницы: 2

Бренд: Char-Broil Страницы: 24

Бренд: BALDR Страницы: 8

Бренд: System Sensor Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды