Avitel 5303 Скачать руководство пользователя страница 7

Страница: 7 / 64

Installation points to remember

This product is designed for fuel-injected, automatic transmission vehicles only.

Installing it in a standard transmission vehicle is dangerous and is contrary to

its intended use.

➤

Virtual tach

Virtual Tach is a new feature for Directed this year. It is the default RPM-sensing

method for the new Responder LE hybrid keyless entry /remote start systems.

Virtual Tach gives the installer the performance of a hard wired tach wire, with

the convenience of voltage sensing. It is far superior to any voltage-sense feature

you’ve tried before.

Virtual Tach monitors the cranking voltage of the vehicle using a very fast micro

controller and an analog-to-digital converter. The microprocessor “saves” the

base voltage as a reference. When Virtual Tach “sees” the slightest uptick in

voltage, indicating that the alternator is charging the battery, the starter motor

shuts off instantly.

➤

D2D

The system has the ability to interface with an XK module through the D2D port.

The advantage to using a D2D interface is that there is less wiring involved in

the installation. Check the XK module installation guide to determine which wires

are not needed, and which options are available.

Содержание 5303





























































Результаты поиска

Содержание 5303

Отзывы:

Похожие инструкции для 5303

Бренды по названию

Популярные бренды

Avitel 5303, Руководство по установке

Результаты поиска

Содержание 5303

Отзывы:

Похожие инструкции для 5303

Бренды по названию

Популярные бренды