Avitel 5303 Скачать руководство пользователя страница 35

Страница: 35 / 64

Step

Function

Auto Learn Standard Configuration (default)

The auto learn configuration will automatically setup the remote

button configuration.

Note:

Due to the Supercode protocol, you

cannot change the configuration.

Delete remotes: This feature will erase all remotes from the memory

of the system. This is useful in cases when a customer’s remote is

lost or stolen.

Note:

Does not reset the programmed features of the

system or reset the Virtual Tach setting.

Reset Features: This resets all the features of the system to the fac-

tory default settings.

Note:

Does not delete the remotes from the

system or reset the Virtual Tach setting.

Virtual Tach Reset: Deletes all previously learned values for Virtual

Tach, and on the next remote start sequence the unit will begin

virtual tach initialization.

Note:

The “Zap” feature on the Bitwriter

does not reset the Virtual tach setting.

4.Transmit. While holding the Valet/Program switch,

press the

button on the remote control. The horn

honks to confirm that the code has been success-

fully programmed. It is not possible to teach a re-

mote control button to the system more than once.

5. Release. Once the code is learned, the Valet/Program

switch can be released.

You can advance from programming one channel to an-

other by releasing the Valet/Program switch and tapping

it to advance channels and then holding it.

Содержание 5303





























































Результаты поиска

Содержание 5303

Отзывы:

Похожие инструкции для 5303

Бренды по названию

Популярные бренды

Avitel 5303, Руководство по установке

Результаты поиска

Содержание 5303

Отзывы:

Похожие инструкции для 5303

Бренды по названию

Популярные бренды