Avitel 5303 Скачать руководство пользователя

Страница: 11 / 64

Making your wiring connections

Before making your connections, plan how your wires will be routed through

the vehicle. For instance, the red 12V constant input and the remote start igni-

tion wires are often routed together to the ignition switch harness. In order to

keep the wiring neat and make it harder to find, you may wish to wrap these

wires together in electrical tape or conceal them in tubing similar to what the

manufacturer used.

There are two acceptable ways of making a wire connection - solder con nec-

tions and crimp connectors. When properly performed, either type of connection

is reliable and trouble-free. Regardless of whether you solder your connections

or you use mechanical type crimp-on connections, ensure that all connections

are mechanically sound and that they are insulated, especially when connecting

data lines in the vehicle.

Cheap electrical tape, especially when poorly applied, is not a reliable insu-

lator. It often falls off in hot weather. Use good quality electrical tape or heat

shrink.

Never twist-and-tape the wires together without soldering.

•

Never use “fuse taps”, as they can damage fuse box terminals.

•

If you use tapping connectors such as T-Taps (not to be confused with Scotch-

Locks), avoid using them in higher-current applications (constant 12V, ground,

etc.) These connectors are inferior in quality and should be avoided.

Содержание 5303





























































Результаты поиска

Содержание 5303

Отзывы:

Похожие инструкции для 5303

Бренды по названию

Популярные бренды

Avitel 5303, Руководство по установке

Результаты поиска

Содержание 5303

Отзывы:

Похожие инструкции для 5303

Бренды по названию

Популярные бренды