Avitel 5303 Скачать руководство пользователя страница 20

Страница: 20 / 64

➤

Auxiliary harness (H2), 6-pin connector

H2/1

LIGHT BLUE

200mA (-) 2nd UNLOCK OUTPUT

This wire produces a (-) 200mA output for progressive locks in which the driver

door unlocks first and the remaining locks unlock with a second press of the

unlock button.

H2/2

WHITE/BLACK

200mA PROGRAMMABLE (-) AUX 2 OUTPUT

This wire provides 200 mA programmable output whenever the transmitter

button(s) controlling Aux 3 is pressed. This output can be programmed to provide

the following types of outputs

Validity: Output that sends a signal as long as the transmission is re-

•

ceived.

Latched: Output that sends a signal when the Aux channel button is pressed

•

and continues until the same button is pressed.

Latched, reset with ignition: Similar to the latched output, this type of output

•

turns On the first time the Aux channel button is pressed, and turns Off the

next time the same button is pressed. This type of output additionally stops

and resets whenever the ignition is turned On and then Off.

30 seconds (60, 90) timed: The output sends a continuous signal for 30

•

seconds.

Note:

Bitwriter® programs from 1 to 90 seconds.

Warning!

Never use this wire to drive anything

but a relay or a low-current input, supplied out-

put is only 200mA. Connecting directly to a

solenoid, motor, or other high-current device

will cause the module to fail.

Содержание 5303





























































Результаты поиска

Содержание 5303

Отзывы:

Похожие инструкции для 5303

Бренды по названию

Популярные бренды

Avitel 5303, Руководство по установке

Результаты поиска

Содержание 5303

Отзывы:

Похожие инструкции для 5303

Бренды по названию

Популярные бренды