Avitel 5303 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 64

background image

18

© 2008 Directed Electronics. All rights reserved.

H1/9

BLACK/WHITE

(-) 200mA DOME LIGHT OUTPUT SUPERVISION OUTPUT

Connect this wire to the optional dome light supervision relay as shown below:

Important! This output is only intended to drive a relay. It cannot be connected

directly to the dome light circuit, as the output cannot support the current draw

of one or more light bulbs.

H1/10

WHITE/BLUE

REMOTE START (-) ACTIVATION INPUT

This input comes from the factory set to 1 activation pulse. This means that it is

necessary to have a two consecutive on ground pulse on the white/blue wire for

the remote start to activate or to deactivate. The same holds true for the remote

control activation it is necessary to press the

button once for the remote start

to activate or deactivate.

Note

:

The number of activation inputs can be programmed to 1 or 2 pulses with

an optional momentary switch. This setting affects both the input wire and the

remote control when operating the remote starter.

To white/blue activation

input on system

«
...
16
17
18
19
20
...
»

Содержание 5303

































































Отзывы:

Нет отзывов

Похожие инструкции для 5303

Бренд: Abus Страницы: 13

Бренд: Ultra Start Страницы: 24

Бренд: Ultra Start Страницы: 28

IntelliGuard 8000

Бренд: Clifford Страницы: 12

Бренд: AVS Страницы: 4

Бренд: C-KO Страницы: 10

Бренд: D+H Страницы: 52

Бренд: iHome Страницы: 21

ALCDVR32-SL V1.0

Бренд: COP-USA Страницы: 12

Бренд: GST Страницы: 2

Бренд: Johnson Controls Страницы: 6

Бренд: Firex Страницы: 8

Бренд: Johnson Controls Страницы: 16

METASYS DH500 Series

Бренд: Johnson Controls Страницы: 32

Бренд: Prestige Страницы: 24

Бренд: ELRO Страницы: 2

Бренд: ELRO Страницы: 32

Бренд: VESDA Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды