Avital AviStart 3200 Скачать руководство пользователя

Страница: 34 / 42

feature menus

Factory default settings are indicated in

bold

in the following feature tables.

FEATURE

DEFAULT - LED ON SETTING

LED OFF SETTING

NUMBER

(PRESS CHANNEL 1)

(PRESS CHANNEL 2)

2-1

Engine checking ON

Engine checking OFF

2-2

Tachometer checking type

Voltage checking type

2-3

12 minutes run time

24 minutes, 60 minutes run time

2-4

Flashing parking light output

Constant parking light output

2-5

Cranking time 0.6 sec. (1)

Cranking time 0.8 (2), 1.0 (3), 1.2 (4), 1.4 (5),
1.6 (6), 1.8 (7), 2.0 (8), 4.0 (9) sec.*

2-6

High voltage check level

Low voltage check level

2-7

Auxiliary output - factory alarm disarm

Auxiliary output - special accessory

2-8

Normal status output

Factory re-arm output

2-9

Anti-Grind ON

Anti-Grind OFF

NOTE:

The numbers in parentheses indicate the number of times the LED will flash.

menu #2

FEATURE

DEFAULT - LED ON SETTING

LED OFF SETTING

NUMBER

(PRESS CHANNEL 1)

(PRESS CHANNEL 2)

1-1

Active arming

Passive arming

1-2

Chirps ON

Chirps OFF

1-3

Ignition controlled door locks ON

Ignition controlled door locks OFF

1-4

Active locking

Passive locking

1-5

0.8 second door lock pulses

3.5 second door lock pulses

1-6

Double pulse unlock OFF

Double pulse unlock ON

1-7

Channel 2 output - Delayed validity (1)*

Channel 2 output - Instant validity (2)/
latched (3)/latched reset with ignition (4)/
30-second timed (5)/second unlock (6)*

1-8

Factory alarm disarm with Channel 2 ON

Factory alarm disarm with Channel 2 OFF

1-9

Stealth Code Hopping ON

Stealth Code Hopping OFF

NOTE:

The numbers in parentheses indicate the number of times the LED will flash.

menu #1

Содержание AviStart 3200











































Результаты поиска

Содержание AviStart 3200

Отзывы:

Похожие инструкции для AviStart 3200

Бренды по названию

Популярные бренды

Avital AviStart 3200, Руководство по установке

Результаты поиска

Содержание AviStart 3200

Отзывы:

Похожие инструкции для AviStart 3200

Бренды по названию

Популярные бренды