Avital AviStart 3200 Скачать руководство пользователя | Manualshive

Страница: 31 / 42

background image

© 2000 Directed Electronics, Inc. Vista, CA

31

transmitter configurations

The transmitters can be programmed with the standard or single button arm/disarm configurations by using the

Auto-learn functions in the Transmitter/Receiver Learn Routine.

A remote that uses the standard configuration operates similarly to many factory keyless entry remotes. A stan-

dard configuration transmitter allows arming, disarming, and Panic Mode activation with separate buttons. When

programmed for standard configuration using the Channel 8 Auto-learn configuration, the transmitter buttons

are assigned to the following functions:

.....................................operates ...........................Arm only

...................................operates ...........................Disarm only

..................................operates ...........................Channel 2

...................................operates ...........................Panic only

and ......................operate............................Remote

Start

When programmed for single button arm/disarm configuration using the Channel 7 Auto-learn configuration, the

transmitter buttons are assigned to the following functions:

.....................................operates ...........................Arm/Disarm/Panic

....................................operates ...........................Channel 2

..................................operates ...........................Remote Start

...................................operates ...........................Channel 3

single button arm/disarm configuration

standard configuration

«
...
29
30
31
32
33
...
»

Содержание AviStart 3200











































Отзывы:

Нет отзывов

Похожие инструкции для AviStart 3200

Бренд: Magicar Страницы: 76

Бренд: Casio Страницы: 1

Бренд: Audiovox Страницы: 8

Prestige Platinum 128-4629B

Бренд: Audiovox Страницы: 21

Бренд: Cofem Страницы: 2

Бренд: Code Alarm Страницы: 8

Бренд: Prestige Страницы: 20

Бренд: Macurco Страницы: 4

Бренд: Char-Broil Страницы: 24

Бренд: La Crosse Страницы: 2

Бренд: iHome Страницы: 12

Бренд: Fire-Lite Страницы: 2

Бренд: Fire-Lite Страницы: 41

Бренд: BALDR Страницы: 8

Бренд: Macurco Страницы: 48

Бренд: Skybrake Страницы: 2

Бренд: DEI Страницы: 26

Бренд: Eurochron Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды