Avital AviStart 3200 Скачать руководство пользователя

Страница: 19 / 42

The Passkey III system can be found in the following vehicles:

■

‘97 and newer Park Avenue

■

‘98 and newer Cadillac

■

‘99 and newer U vans, Transport, Montana, and Silhouette

■

2000 and newer Grand Prix, Lesabre, Monte Carlo, Lumina, Bonneville

■

2001 and newer Aurora, Aztek and Rendezvous

Other transponder-based systems include: Acura, BMW, Dodge/Chrysler/Jeep, Ford, Honda, Infinity, Mazda,

Mercedes, Mitsubishi, Nissan, Toyota, Volkswagon, and Volvo.

PK-3 and the transponder-based systems use a transponder system that locks out the ignition and fuel system.

This transponder system is comprised of two parts. The first part, the transceiver, circles the key switch

and is activated when the key is placed in the key switch or turned to the run position. Upon activation, the

transceiver will excite the transponder, which is located (but not visible) in the head of the ignition key. The key

transponder will then send a unique code back to the transceiver for evaluation. If the code matches a

valid code of the system, the vehicle will be allowed to start. Most of these transponder-based systems can be

bypassed using

p/n 555U.

Some may require additional parts from the vehicle manufacturer. Consult you dealer

for the applications. For most Ford PATS transponders, as well as Lexus and Toyotas,

p/n 555F

can be used, except

for the following vehicles, which will require

p/n 555U

: ‘97 and newer Mark VII, and 2000 and newer

Taurus/Sable, Contour/Mystique and Focus.

bypassing GM vehicle anti-theft systems (VATS)

Vehicles with the GM VATS (Pass Key) systems have a resistor embedded in the ignition key. If the VATS decoder

module does not measure the proper resistance when the vehicle is started, the starter and fuel pump may be

disabled for up to ten minutes. An optional "VATS pack" of resistors is available

(p/n 652T)

. One of the resistors in

the pack will match the resistor in the key.

The VATS wires will be two very light-gauge wires coming out of the steering column. The colors of the wires vary,

but they are often contained in orange tubing - either both will be white wires, or one wire will be purple/white

and the other white/black. Determine the value of the resistor in the key. Then follow the diagram below to

bypass VATS during remote start operation. If the BLUE status output has been programmed for factory security

re-arm, use the H3/2 BLUE/BLACK third ignition output to control the relay.

passkey III (PK-3), transponder-based systems

Содержание AviStart 3200











































Результаты поиска

Содержание AviStart 3200

Отзывы:

Похожие инструкции для AviStart 3200

Бренды по названию

Популярные бренды

Avital AviStart 3200, Руководство по установке

Результаты поиска

Содержание AviStart 3200

Отзывы:

Похожие инструкции для AviStart 3200

Бренды по названию

Популярные бренды