Avital AviStart 3200 Скачать руководство пользователя

Страница: 7 / 42

wiring diagrams

The primary harness supplied with this unit is the standard 12-pin harness used by DEI

security systems. Three

wires in the plug are not used. The upgrade from this unit to a security system would simply require unplugging

and exchanging control units and connecting the necessary wires to the vehicle. The functions of all the wires

that are used in the primary harness are outlined in the following wiring diagram and the wire connections are

described in the wire connection guides.

______

RED

(+) CONSTANT POWER

YELLOW

(+) IGNITION INPUT TO REMOTE START

PINK

(-) 200

A IGNITION RELAY TURN-ON

ORANGE

(-) 200

A ACCESSORY RELAY TURN-ON

PURPLE

(-) 200

A STARTER RELAY TURN-ON

remote start ribbon harness wiring diagram

RED/WHITE

(-)200

A CHANNEL 2 PROGRAMMABLE OUTPUT

RED

(+) CONSTANT POWER INPUT

BROWN

(-) HORN H0NK OUTPUT

YELLOW

(+) IGNITION (OUTPUT TO OPTIONAL SECURITY SYSTEM)

BLACK

(-) CHASSIS GROUND INPUT

VIOLET

NO FUNCTION

BLUE

NO FUNCTION

GREEN

NO FUNCTION

BLACK/WHITE

(-)200

A DOMELIGHT SUPERVISION OUTPUT

WHITE/BLUE

(-) REMOTE START ACTIVATION INPUT

WHITE

(+)/(-) SELECTABLE LIGHT FLASH OUTPUT

ORANGE

(-) 500

A ARMED OUTPUT

H1/1

H1/2

H1/3

H1/4

H1/5

H1/6

H1/7

H1/8

H1/9

H1/10

H1/11

H1/12

primary harness (H1) wiring diagram

Содержание AviStart 3200











































Результаты поиска

Содержание AviStart 3200

Отзывы:

Похожие инструкции для AviStart 3200

Бренды по названию

Популярные бренды

Avital AviStart 3200, Руководство по установке

Результаты поиска

Содержание AviStart 3200

Отзывы:

Похожие инструкции для AviStart 3200

Бренды по названию

Популярные бренды