Avital AviStart 3200 Скачать руководство пользователя

Страница: 15 / 42

This wire MUST be connected to hood pinswitch. This input will disable or shut down the remote start when the hood

is opened.

This wire MUST be connected to the vehicle's brake light wire. This is the wire that shows (+) 12V when the brake

pedal is pressed. The remote start will be disabled or shut down any time the brake pedal is pressed.

This input provides the module with information about the engine's revolutions per minute (RPMs). It can be

connected to the negative side of the coil in vehicles with conventional coils. In multi-coil and high energy igni-

tion systems locating a proper signal may be more difficult. (See

Installation Points to Remember

section of this

guide for finding the tachometer wire.) Once connected, you must teach the system the tach signal. (See

Tach

Learning

section of this guide.)

Connect this wire to the toggle (override) switch as shown in Figure A. Connect the other wire from the toggle

switch to the PARK/NEUTRAL switch in the vehicle. This wire will test with ground with the gear selector either

in PARK or NEUTRAL. This will prevent the vehicle from accidentally being started while in a drive gear. This input

MUST rest at ground in order for the remote start system to operate. Connected properly the vehicle will only

start while in PARK or NEUTRAL.

In some vehicles, the PARK/NEUTRAL position switch activates a factory starter lock out that will not allow the

starter to operate in a drive gear. In these vehicles, connect this wire to the toggle switch as shown in Figure

B. Connect the other wire from the toggle switch to chassis ground.

Figure A

Figure B

IMPORTANT!

Always perform the Vehicle Safety Check section of this guide to verify that the vehicle

cannot be started in ANY drive gear and that the override switch is functioning properly.

H3/6 BLACK/WHITE neutral safety switch input

H3/5 VIOLET/WHITE tachometer input

H3/4 BROWN (+) brake switch input

H3/3 GRAY (-) hood pinswitch input

Содержание AviStart 3200











































Результаты поиска

Содержание AviStart 3200

Отзывы:

Похожие инструкции для AviStart 3200

Бренды по названию

Популярные бренды

Avital AviStart 3200, Руководство по установке

Результаты поиска

Содержание AviStart 3200

Отзывы:

Похожие инструкции для AviStart 3200

Бренды по названию

Популярные бренды