Avital AviStart 3200 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 42

background image

© 2000 Directed Electronics, Inc. Vista, CA

13

Connect this wire to the second ignition wire in the vehicle.

auxiliary harness (H2) wire connection guide

This wire sends a negative pulse every time the remote start is activated. This can be used to pulse the disarm

wire of the vehicle's factory anti-theft device. Use a relay to send a (-) or (+) pulse to the disarm wire as shown

in the diagrams below. This wire can also be used as a special accessory output. (See

Feature Descriptions

section

of this guide.)

Relay for Negative (-) Disarm Wire

Relay for Positive (+) Disarm Wire

Connect this wire to the wire in the vehicle that sends the signal to turn on the WAIT-TO-START bulb in the dash-

board. In most diesels the wire is negative (ground turns on the bulb) and the GRAY/BLACK can be directly

connected to the wire in the vehicle. If the vehicle uses a positive wire (12V to turn on the bulb) a relay must

be used to change the polarity. (See

Finding the Wait-To-Start Bulb Wire For Diesels

section of this guide.) Here are

some common colors of this wire:

■

Chevrolet and GMC trucks: Light Blue or Dark Blue

■

Ford Trucks: Black/Pink

■

Dodge Ram Trucks: Orange/Black or Black/Orange

NOTE!

A 1-amp diode must be installed in line on the factory wire between the wait-to-start indi-

cator and the ECM. (See the following diagram for details.)

H2/2 GRAY/BLACK (-) diesel wait-to-start bulb input

H2/1 LIGHT GREEN/BLACK (-) auxiliary output

PINK/WHITE (+) output to second ignition circuit

«
...
11
12
13
14
15
...
»

Содержание AviStart 3200











































Отзывы:

Нет отзывов

Похожие инструкции для AviStart 3200

RADIO CONTROLLED PROJECTION ALARM CLOCK

Бренд: La Crosse Technology Страницы: 25

Бренд: ThermoWorks Страницы: 2

Бренд: La Crosse Technology Страницы: 6

Бренд: Casio Страницы: 3

Бренд: iHome Страницы: 12

Бренд: Kidde Страницы: 18

Бренд: Geemarc Страницы: 2

Бренд: Naxa Страницы: 10

Бренд: iHome Страницы: 24

Бренд: Toyota Страницы: 12

Бренд: Sylvania Страницы: 8

Бренд: Sylvania Страницы: 17

Бренд: iBeam Страницы: 2

Бренд: BALANCE TIME Страницы: 6

CRA54 - Digital Alarm Clock

Бренд: Coby Страницы: 1

Prestige Platinum APS-400

Бренд: Prestige Страницы: 24

Prestige Platinum APS 600

Бренд: Prestige Страницы: 27

Бренд: Secutron Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды