background image

 

     

 

 

CS-883 OEM 

 

ALARM UPGRADE FOR FACTORY KEYLESS ENTRY SYSTEMS 

 

INSTALLATION & OPERATING INSTRUCTIONS 

 

 

INTRODUCTION 

 

CONGRATULATIONS

 on your choice of an Alarm Upgrade System by Crimestopper Security Products Inc.  This 

booklet  contains  the  information  necessary  for  installing,  using,  and  maintaining  this  system.    If  any  questions 
arise, contact your installation dealer or Crimestopper Security Products Inc. at the Tech Support number below. 

 
 

*IMPORTANT INFORMATION:

 

 

This system does not improve or affect the range of the factory remote keyless entry transmitters.  This is 
an  ADD-ON  system  only.    The  arm/disarm  range  of  this  system  will  be  identical  to  that  of  the  Factory 
Keyless System’s lock/unlock range.

 

 

This  installation  book  is  designed  for  the  installer  or  individual  with  an  existing  understanding  of  automotive 
electrical systems, along with the ability to test and connect wires for proper operation.  To ease installation, we 
suggest  that  you  READ  THIS  MANUAL  before  beginning  your  installation.    The  information  contained  in  this 
manual is provided as a GENERAL GUIDLINE and it may differ from your vehicle!  If you are not confident with 
performing the installation steps as required by this system, we suggest seeking professional installation. 

 

TECH SUPPORT 

Mon-Fri 8:00 AM-4:30 PM Pacific Time 

(800) 998-6880 

 

REV.  A  02.2009 

 
 
 
 

Содержание CS-883 OEM













Отзывы: