background image

 

12 

OPERATING INSRUCTIONS 

 

VALET MODE 

To disable alarm functions of the 883 system, turn the Ignition ON and press the override/program button 3 times 
within 8 seconds. Turn off ignition, after 8 seconds, the dash LED turns on solid as an indicator that the system is 
in valet mode.  Repeat these steps to exit VALET mode.  The LED will go out, system will chirp (2) times and the 
light will flash (2) times when exiting valet mode.  

 

When  in  VALET  mode  the  siren  will  still  chirp  for  lock/unlock  confirmation  even  though  alarm  functions  are 
disabled.  The CS-883 system will chirp 2 times when locking the doors and 3 times when unlocking the doors. 

 

PANIC MODE (Programmable Option) 

To  activate  your  system  during  an  emergency  situation  or  to  attract  attention  to  your  vehicle,  press  the  Lock 
button on your remote 3 times within 5 seconds.  This will activate a 30-second alarm trigger.  Press any button 
on your remote to disarm. 

 

FACTORY TRUNK RELEASE SENSING 

If the CS-883 system is installed in a vehicle with trunk pop or hatch release button on the Factory Remote, there 
is  a  special  input  wire  that  will  prevent  the  system  from  triggering  if  the  trunk  button  on  your  remote  is  pressed 
while the system is armed. 
 

OPEN DOOR WARNING 

If the vehicle door is left open  when arming system,  you will hear 5-siren chirps after 10 seconds.  This may be 
programmed for a 1-minute delay for vehicles with delayed dome lights using program option #2. 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

Содержание CS-883 OEM













Отзывы: