Avaya P332GT-ML Скачать руководство пользователя страница 42

Страница: 42 / 150

Chapter 6

Avaya P332GT-ML Front and Rear Panels

Avaya P332GT

-ML User’s Guide

OPR

CPU Operation

OFF – Module is booting

ON – Normal operation

SYS

System Status

OFF – Module is a slave in a stack

ON – Module is the master of the stack and
the Octaplane and Redundant (optional)
cable(s) are connected correctly.
This LED will also light in Standalone mode.

Blink – Box is the master of the stack and the
Octaplane is in redundant mode.

ROUT

Routing Mode

OFF – Layer 2 mode

ON – Router mode

The following Function LEDs apply to all ports

LNK

Port Status

ON – Link is OK
OFF – Port is disabled
Blink – Port is enabled, but Link is down

COL

Collision

Always OFF. All ports are full-duplex only.

Transmit to line

OFF – No transmit activity

ON – Data transmitted on line from the
module

Receive from line

OFF – No receive activity

ON – Data received from the line into the
module

FDX

Full Duplex mode

Always ON. All ports are full-duplex only.

Table 6.1

Avaya

P332GT-ML

LED Descriptions (Continued)

LED Name

Description

LED Status

Содержание P332GT-ML























































































































































Результаты поиска

Содержание P332GT-ML

Отзывы:

Похожие инструкции для P332GT-ML

Бренды по названию

Популярные бренды

Avaya P332GT-ML, Руководство по установке и настройке

Результаты поиска

Содержание P332GT-ML

Отзывы:

Похожие инструкции для P332GT-ML

Бренды по названию

Популярные бренды