Avaya P332GT-ML Скачать руководство пользователя страница 121 | Manualshive

Страница: 121 / 150

background image

Chapter 12

Avaya P330 Layer 3 Features

Avaya P332GT

-ML User’s Guide

107

VRRP Configuration Example 1

Figure 12.3

VRRP Configuration Example (Case 1, Case 2)

Case#1

One main router on IP subnet 20.20.20.0 (P333R/P330-ML or any third-party router
which supports VRRP) and a redundant router (more backup routers may be
configured)
•

The P330 itself must have an interface on the IP subnet (e.g. 20.20.20.2)

•

All the routers are configured under the same VRID (Virtual Router ID- e.g.1)
This configuration must be done per VLAN).

•

The P330 requires that this VRID must not be used in the network (even in
different VLAN)

•

By the end of the routers configuration, and when the network is up, the main
router for each virtual router will be elected according to this order of
preference:
— The virtual router IP address is also the router’s interface IP address
— It has the highest priority (you can configure this parameter)
— It has the highest IP address if the previous cases do not apply

Backup Router 1

VRID: 1, IP: 20.20.20.2

Ass. IP: 20.20.20.1

VMAC: 00005E000101 (VRID)

Main Router 2

VRID: 2, IP: 30.30.30.1=Ass. IP

Backup Router 2

VRID: 2, IP: 30.30.30.2

Ass. IP: 30.30.30.1

VMAC: 0005E000102 (VRID)

Main Router 1

VRID: 1, IP: 20.20.20.1=Ass. IP

IP: 30.30.30.20

IP: 20.20.20.10

DG: 20.20.20.1

IP: 20.20.20.20

IP: 30.30.30.10

DG: 30.30.30.1

«
...
119
120
121
122
123
...
»

Содержание P332GT-ML























































































































































Отзывы:

Нет отзывов

Похожие инструкции для P332GT-ML

Бренд: UNICOM Страницы: 1

Бренд: D-Link Страницы: 17

Бренд: OEM Страницы: 1

Бренд: EtherWAN Страницы: 2

Link Power LPS2400-T1

Бренд: Inscape Data Страницы: 8

QuantaMesh T4000 Series

Бренд: QCT Страницы: 41

Бренд: Shinybow USA Страницы: 16

SmartSTACK ETHERNET ELS10-27

Бренд: Cabletron Systems Страницы: 126

Instant On 1930 Series

Бренд: Aruba Страницы: 8

Бренд: Linkskey Страницы: 2

Бренд: tactio Страницы: 2

Бренд: ICCN Страницы: 48

Бренд: IPGARD Страницы: 15

Бренд: Hubner Страницы: 23

Бренд: Link Страницы: 35

Бренд: Blagdon Страницы: 6

24/48 10/100 Ports + 2GE

Бренд: Accton Technology Страницы: 512

Бренд: DeviceWell Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды