Avaya P332GT-ML Скачать руководство пользователя страница 55

Страница: 55 / 150

Chapter 8

User Authentication

Avaya P332GT

-ML User’s Guide

Radius Commands

The following radius commands are accessible from Supervisor level.

For a complete description of the RADIUS CLI commands, including syntax and
output examples, refer to

Avaya P330: Reference Guide

In order to...

Use the following command...

Enable or disable authentication for
the P330 switch. RADIUS
authentication is disabled by
default

set radius authentication

Set a primary or secondary
RADIUS server IP address

set radius authentication server

Configure a character string to be
used as a “shared secret” between
the switch and the RADIUS server.

set radius authentication secret

Set the RFC 2138 approved UDP
port number.

set radius authentication udp-port

Set the number of times an access
request is sent when there is no
response

set radius authentication retry-
number

Set the time to wait before re-
sending an access request.

set radius authentication retry-time

Remove a primary or secondary
RADIUS authentication server

clear radius authentication server

Display all RADIUS authentication
configurations. The shared secrets
will not be displayed

show radius authentication

Содержание P332GT-ML























































































































































Результаты поиска

Содержание P332GT-ML

Отзывы:

Похожие инструкции для P332GT-ML

Бренды по названию

Популярные бренды

Avaya P332GT-ML, Руководство по установке и настройке

Результаты поиска

Содержание P332GT-ML

Отзывы:

Похожие инструкции для P332GT-ML

Бренды по названию

Популярные бренды