Avaya P332GT-ML Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 150

background image

Chapter 4

Installation

20

Avaya P332GT

-ML User’s Guide

Installing the X330STK-ML Stacking Sub-Module (Optional)

Caution:

The stacking sub-modules contain components sensitive to electrostatic

discharge. Do not touch the circuit board unless instructed to do so.

To install the stacking sub-module in the P332GT-ML:
1

Remove the blanking plate from the back of the P332GTP332GT-ML switch.

2

Insert the stacking sub-module gently into the slot, ensuring that the metal base
plate is aligned with the guide rails. The metal plate of the X330STK-ML (and

not

the PCB) fits onto the guide rails.

3

Press the sub-module in firmly until it is completely inserted into the

P332GT

P332GT-ML.

4

Gently turn the two screws on the side panel of the stacking sub-module until
they are secure.

Note:

The P332GTP332GT-ML must not be operated with the back-slot open. The

stacking sub-module should be covered with the supplied blanking plate if necessary.

Note:

Only use the X330STK-ML stacking module with the P332GTP332GT-ML.

Connecting Stacked Switches

Note:

The two ends of the Octaplane cable terminate with different connectors. Each

connector can only be connected to its matching port.

The following cables are used to connect stacked switches:
•

Short Octaplane cable (X330SC) – ivory-colored, used to connect adjacent
switches (Catalog No. CB0223) or switches separated by a BUPS unit.

•

Long/Extra Long Octaplane cable (X330LC/X330L-LC) – ivory-colored, used to
connect switches from two different physical stacks, or switches separated by a
BUPS unit (Catalog No. CB0225/CB0270).

•

Redundant/Long Redundant Octaplane cable (X330RC/X330L-RC) – black,
used to connect the top and bottom switches of a stack (Catalog No. CB0222/
CB0269).

These are the same cables that are used with all the P330 switches.

«
...
32
33
34
35
36
...
»

Содержание P332GT-ML























































































































































Отзывы:

Нет отзывов

Похожие инструкции для P332GT-ML

SANbox 5000 Series

Бренд: Qlogic Страницы: 8

xStack DGS-3427

Бренд: D-Link Страницы: 246

Бренд: Hansen Страницы: 4

Бренд: Indu-Sol Страницы: 9

SEHI SEHI100TX-

Бренд: Cabletron Systems Страницы: 75

S5560S-EI Series

Бренд: H3C Страницы: 47

S3100-16T P-EI-W

Бренд: H3C Страницы: 60

Бренд: ABM Страницы: 8

Бренд: I-Tech Страницы: 19

Бренд: Linkskey Страницы: 2

Бренд: Allied Telesis Страницы: 44

CUVEO CR-UPS2000

Бренд: Me Страницы: 44

forerunner series

Бренд: Fore Systems Страницы: 352

DG-GS4900SE Series

Бренд: Digisol Страницы: 23

S5700-24F-8G-4TF

Бренд: Hored Страницы: 28

LAN MASTER 33022.B

Бренд: Transition Networks Страницы: 12

Бренд: NETGEAR Страницы: 2

AMX DVX-2265-4K

Бренд: Harman Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды