Avaya P332GT-ML Скачать руководство пользователя страница 141 | Manualshive

Страница: 141 / 150

background image

Avaya P332GT

-ML User’s Guide

127

Chapter 14

Troubleshooting the Installation

Troubleshooting the Installation

This section will allow you to perform basic troubleshooting of the installation. If
you are unable to solve the problem after following the procedures in this chapter,
please contact Avaya Technical Support. Refer to “How to Contact Us“for full
details.

Table 14.1

Troubleshooting

Problem/Cause

Suggested Solution

Switch does not power up

• AC power cord not inserted

or faulty

• Check that the AC power cord is

inserted correctly

• Replace the power cord

If the cord is inserted correctly, check that the AC power source is working by
connecting a different device in place of the P3330.
• If that device works, refer to the next step.
• If that device does not work, check the AC power

• P3330 AC power supply not

functioning

• Use an optional BUPS (Backup Power

Supply)

• Contact your local Avaya distributor.

The

power supply is not user-replaceable.

Stacking not functioning

• X330-STK modules not

inserted correctly
(LEDs on stacking module
do not light)

• Check that modules are installed

correctly

• Octaplane™ cables not

installed correctly
(LEDs on stacking module
do not light)

• Check that the cables are inserted

correctly

• Check that there are no cross-corrections

«
...
139
140
141
142
143
...
»

Содержание P332GT-ML























































































































































Отзывы:

Нет отзывов

Похожие инструкции для P332GT-ML

Бренд: Keithley Страницы: 66

Бренд: Cisco Страницы: 30

Baseline 2226 Plus

Бренд: 3Com Страницы: 4

Бренд: Gavita Страницы: 12

Бренд: JAR Systems Страницы: 2

Бренд: Surefire Страницы: 2

Бренд: Lindy Страницы: 4

IES2016-16T Series

Бренд: 3onedata Страницы: 3

SBX 95 SE - AV Control 4

Бренд: Vivanco Страницы: 16

Бренд: NVision Страницы: 92

Бренд: National Instruments Страницы: 8

Бренд: Abtus Страницы: 2

EX78900X Series

Бренд: EtherWAN Страницы: 2

Бренд: Grizzly Страницы: 2

Бренд: Cabletron Systems Страницы: 83

Бренд: H3C Страницы: 53

Бренд: Eaton Страницы: 4

Бренд: Eaton Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды