Avaya P332GT-ML Скачать руководство пользователя страница 90

Страница: 90 / 150

Chapter 11

Avaya P330 Layer 2 Features

Avaya P332GT

-ML User’s Guide

IP Multicast CLI Commands

The following table contains a list of the CLI commands for the IP Multicast feature.
The rules of syntax and output examples are all set out in detail in the

Reference

Guide

Table 11.7

IP Multicast CLI Commands

IP Multicast Implementation in the Avaya P332GT-ML

This section describes the implementation of the IP multicast feature in the Avaya

P332GT-ML

•

No. of multicast groups — 1000

In order to...

Use the following command...

Enable or disable the IP multicast
filtering application

set intelligent-multicast

Define aging time for client ports

set intelligent-multicast client port
pruning time

Define aging time for router ports

set intelligent-multicast router port
pruning time

Define group filtering time delays

set intelligent-multicast group-
filtering delay time

Display the status IP multicast
filtering application

show intelligent-multicast

Shows whether the connected
unit’s hardware supports IP
multicast filtering

show intelligent-multicast
hardware-support

Содержание P332GT-ML























































































































































Результаты поиска

Содержание P332GT-ML

Отзывы:

Похожие инструкции для P332GT-ML

Бренды по названию

Популярные бренды

Avaya P332GT-ML, Руководство по установке и настройке

Результаты поиска

Содержание P332GT-ML

Отзывы:

Похожие инструкции для P332GT-ML

Бренды по названию

Популярные бренды