Avaya P332GT-ML Скачать руководство пользователя страница 43

Страница: 43 / 150

Chapter 6

Avaya P332GT-ML Front and Rear Panels

Avaya P332GT

-ML User’s Guide

Note:

All LEDs are lit during reset.

Flow Control

OFF – No flow control.

ON – One of the three possible flow control
modes is

enabled

Note:

FC LED for Gigabit Ethernet ports

reflect the last negotiated mode when
autonegotiation is enabled and the link is
down.

Hspd

High Speed

Ports 1-10

Ports 51,52

OFF:

100 Mbps N/A

ON:

1000 Mbps 1000 Mbps

LAG

Link Aggregation
Group (Trunking)

OFF – No LAG defined for this port

ON – Port belongs to a LAG

Table 6.2

Avaya

P332GT-ML

<- -> Select buttons

Description

Function

Left/Right

Individual – select LED function (see table above)

Reset module

Press both right and left buttons together for approximately 2
seconds. All LEDs on module light up until buttons are
released.

Reset stack

Press both Right and Left buttons together for 4 seconds. All
LEDs on stack light up until buttons are released.

Table 6.1

Avaya

P332GT-ML

LED Descriptions (Continued)

LED Name

Description

LED Status

Содержание P332GT-ML























































































































































Результаты поиска

Содержание P332GT-ML

Отзывы:

Похожие инструкции для P332GT-ML

Бренды по названию

Популярные бренды

Avaya P332GT-ML, Руководство по установке и настройке

Результаты поиска

Содержание P332GT-ML

Отзывы:

Похожие инструкции для P332GT-ML

Бренды по названию

Популярные бренды