Avaya IP Office Phone Manager Скачать руководство пользователя страница 112 | Manualshive

Страница: 112 / 411

Avaya IP Office Phone Manager Скачать руководство пользователя страница 112

IP Office Installation

Page 111

15-601042 Issue 20b (16 July 2009)

IP Office

IP400 Basic Installation: Unpacking

6.2 Installing the Admin Applications

This procedure covers installation of applications in the IP Office Admin suite.

Objective -

To install the applications necessary for the installation and maintenance of an IP

Office system.

Information Required

1.

o

Which IP Office Admin Suite applications are being installed?

The following list indicates those that are required for installation and configuration:

•

o

System Monitor - Install

Monitor is a tool intended primarily for Avaya technicians and engineers. However it is able to report on all aspects
of IP Office operation and is therefore an important tool for diagnostics.

•

o

Feature Key Server - Not required.

The Feature Key Server should only be installed if the PC will host the parallel port or USB port Feature Key dongle
for the IP Office system.

•

o

Manager - Install

This application is required to edit and manage the software on the IP Office system.

•

o

System Status Application - Install

This application is used with IP Office 4.0 systems to show equipment and resource within the system, alarms and
calls in progress.

•

o

Previous System Monitor - Not required.

This application is only required for supporting IP400 systems running pre-IP Office 4.0 software. It is not required
for IP500 control units.

•

o

Call Status - Not required.

This application is only supported for pre-4.0 IP Office systems. For IP Office 4.0 and higher it has been replaced
by the System Status Application above.

Parts Required

•

o

IP Office Administrator Applications CD.

•

o

Windows PC

This should meet the requirements of the administrator applications being installed. If a server PC from the
customer installation is available, for example for Voicemail Pro, use that PC. The specification below is just for IP
Office Manager. If other applications are to be installed on the PC then their requirements should also be meet.

Requirement

Minimum

Recommended

Processor

600MHz Pentium or AMD Opteron, AMD Athlon64,
AMD Athlon XP.

800MHz Pentium or AMD Opteron, AMD
Athlon64, AMD Athlon XP.

RAM

128MB

256MB

HD Space

1GB - 800MB for .NET2, 200MB for Manager.

1.4GB - 800MB for .NET2, 600MB for the full
IP Office Admin suite.

Display

800 x 600 - 256 Colors

1024 x 768 - 16-bit High Color

Operating
System

Windows XP Professional with SP2. Windows 2003 Server. Windows 2003 SBS. Note: 64-bit
versions of the operating systems above are not supported.

«
...
110
111
112
113
114
...
»

Содержание IP Office Phone Manager




























































































































































































































































































































































































































Отзывы:

Нет отзывов