AutoCrib RoboCrib 2000 E Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 53

background image

Troubleshooting

31 |

P a g e

Problem: The LED on Door Remains On

1. Adjustment of the front-side solenoid encoder



Turn the controller off.



Remove the left door screws and open the left door.



Open the door by pulling the manual release lever.



Remove the solenoid cover bracket.



Adjust the front encoder (U4 position on the board) that is next to the LED light to the right.

o

Use a non-magnetic flathead screwdriver and place it in between the encoder and the plunger

guide wall.

o

Push off the plunger guide wall gently and adjust the sensor towards the right.

o

Turn the controller on and close the door. If the LED turned off, attempt to issue from the

RoboCrib. If the RoboCrib dispenses correctly, no further troubleshooting is required.

2. Adjustment of the back-side solenoid encoder



Turn the controller off.



Adjust the back encoder (U3 position on the board) that is behind the solenoid against the back wall
of the door.

o

Use a non-magnetic flathead screwdriver and place it in between the encoder and the plunger

wall.

o

Push off the back part of the wall gently and adjust the sensor toward the front or towards the

user.

o

Turn the controller on and close the door. If the LED turned off, attempt to issue from the

RoboCrib. If the RoboCrib dispenses correctly, no further troubleshooting is required.

o

If the LED does not turn off, use the spare door provided with the RoboCrib. Contact AutoCrib

technical support to receive a replacement door.

«
...
29
30
31
32
33
...
»

Содержание RoboCrib 2000 E






















































Отзывы:

Нет отзывов

Похожие инструкции для RoboCrib 2000 E

Бренд: Canon Страницы: 115

Tekken Tag Tournament

Бренд: NAMCO Страницы: 59

Бренд: NAMCO Страницы: 29

Бренд: Baby Lock Страницы: 198

Бренд: Elba Страницы: 17

Бренд: WAHLAP TECH Страницы: 121

Бренд: UNIS Страницы: 27

Бренд: Saeco Страницы: 32

Бренд: Radio Shack Страницы: 24

Бренд: Singer Страницы: 46

Бренд: Parkeon Страницы: 127

Бренд: Duerkopp Adler Страницы: 84

Бренд: Xerox Страницы: 92

Бренд: Olivetti Страницы: 16

Бренд: Olympia Страницы: 22

Бренд: Singer Страницы: 24

Бренд: Baby Lock Страницы: 33

Бренд: JUKI Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды