AutoCrib RoboCrib 2000 E Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 53

background image

Installation

12 |

P a g e

Check Platter Actuation

1. Test each motor clockwise (CW) and counter-clockwise (CCW) for

a few seconds.



Position the Direction switch in either the CW or CCW position.
Then, activate the Motor Switch.



Observe proper rotation. Then, reverse the Direction switch
and test again.



As  each  Motor  switch  is  actuated,  the  appropriate  platter
should  turn,  and  the  sensor  lights  should  blink.   While  testing
each  motor,  please  note  how  the  platters  should  react  to  the
movement.    See  the  appendix  for  a  drawing  of  the  motors,
platters, and bins.

2. Test the door baffle by positioning the Direction switch in either the

CW or CCW position and actuating the Baffle switch.

Main:

Main Platter

– the entire internal array

will rotate

LSP:

Large Sub Platter

– 3 individual and 3

groups of 3 trays assemblies will rotate

SS3, 2, 1:

Small Sub Platters

– Individual tray

assemblies in groups of 3 will rotate

SWITCH DEFINITIONS

MP = MAIN PLATTER
LSP = LARGE SUB PLATTER
SSP3 = SMALL SUBPLATTER #3
SSP2 = SMALL SUB PLATTER #2
SSP1 = SMALL SUB PLATTER #1

«
...
10
11
12
13
14
...
»

Содержание RoboCrib 2000 E






















































Отзывы:

Нет отзывов

Похожие инструкции для RoboCrib 2000 E

Бренд: Janome Страницы: 48

Бренд: Jack Страницы: 7

Бренд: Jack Страницы: 22

Бренд: Samsung Страницы: 72

WF1804WP series

Бренд: Samsung Страницы: 88

Бренд: Daedalus Страницы: 20

Бренд: Jack Страницы: 8

Бренд: Jack Страницы: 10

Бренд: Ricoh Страницы: 116

Бренд: Necta Страницы: 23

Бренд: Janome Страницы: 115

Бренд: JUKI Страницы: 149

Бренд: Janome Страницы: 43

ellegante 2 BLG2

Бренд: Baby Lock Страницы: 8

Бренд: Husqvarna Страницы: 184

796.3155 series

Бренд: Kenmore Страницы: 34

Бренд: Panasonic Страницы: 33

Бренд: Panasonic Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды