AutoCrib RoboCrib 2000 E Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 53

background image

Dispensing Machine Limited Warranty

AutoCrib provides depot level warranty coverage, which is defined as:

Depot level warranty means a new part/subsystem/machine will be shipped overnight to you or your
authorized distributor and billed to you or your distributor at the then current price.  Your distributor is
required to ship the defective part/subsystem/machine back to AutoCrib within 30 days from the ship
date of the replacement part.  You agree to contact AutoCrib customer service and get an

“RMA”

(return material authorization) number before you ship the defective part back. Upon receiving the
defective part, AutoCrib will issue an offsetting credit to your company or authorized distributor per
your instruction.

Limitations and Exclusions

This warranty shall not cover or include any of the following and AutoCrib shall have no liability with
respect to:

1. Defects or damages which result from accident, misuse, abuse, lack of recommended or

reasonable maintenance, improper repairs or parts replacements, use of replacement parts not
conforming to AutoCrib standards, unauthorized modifications or general neglect including
electrical spikes, surges and sags caused by poor power management, thunderstorms or acts
of god or lack of normal power conditioning for electronic manufacturing equipment.

2. Damage caused by exposure to liquid spills, collision, fire, theft, freezing, vandalism, riot, war,

explosion or objects striking the machine such as fork trucks or exposure to abnormally
corrosive conditions or entry by insect or vermin or foreign objects or mispackaged or
misplaced product inside the machine.

3. Routine replacement main of consumable parts such as but not limited to light bulbs, plastic

breakable lock boxes, batteries, RFID tags, printer paper rolls, printer cartridges etc.

4. Routine maintenance services such as lubrications of drive trains or actuation solenoids. (See

appropriate AutoCrib manual for details)

5. Subsystems and attachments to the hardware/machine not manufactured by AutoCrib that are

subject to warranties of the manufacturers of such items. Ie. Uninterruptible power supplies,
surge protectors etc.

Modifications and Upgrades

AutoCrib reserves the right to make certain changes in designs or changes and improvements in
its products at any time without obligation to make such changes or improvements in its products
previously manufactured.

«
1
2
3
4
5
...
»

Содержание RoboCrib 2000 E






















































Отзывы:

Нет отзывов

Похожие инструкции для RoboCrib 2000 E

Бренд: Pfaff Страницы: 68

Бренд: Mitsubishi Страницы: 61

Autopax PAX600H

Бренд: Quasar Страницы: 148

Бренд: NAMCO Страницы: 44

Бренд: Singer Страницы: 24

HZL - 353Z Series

Бренд: JUKI Страницы: 35

Бренд: SunStar Страницы: 36

Бренд: Paitec Страницы: 21

Бренд: Xblue Networks Страницы: 24

SE 350 - Compact Sewing & Embroidery Combo Machine

Бренд: Brother Страницы: 2

Бренд: Brother Страницы: 6

Бренд: Brother Страницы: 74

Бренд: Brother Страницы: 6

Бренд: Brother Страницы: 80

Бренд: Brother Страницы: 47

Бренд: Brother Страницы: 84

Бренд: Brother Страницы: 67

Бренд: Brother Страницы: 53

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды