manualshive.com logo in svg

AUMA SG 04.2, Руководство по эксплуатации

Поделиться
Скачать
AUMA SG 04.2 Скачать руководство пользователя страница 2

Read operation instructions first.

●

Observe safety instructions.

●

These operation instructions are part of the product.

●

Store operation instructions during product life.

●

Pass on instructions to any subsequent user or owner of the product.

Target group:

This document contains information for assembly, commissioning and maintenance staff.

Reference documents:

Reference documents can be downloaded from the Internet (www.auma.com) or ordered directly from AUMA
(refer to <Addresses>).

Table of contents

Page

4

1.

Safety instructions.................................................................................................................

4

1.1.

Prerequisites for the safe handling of the product

4

1.2.

Range of application

5

1.3.

Warnings and notes

5

1.4.

References and symbols

6

2.

Short description...................................................................................................................

7

3.

Name plate..............................................................................................................................

9

4.

Transport and storage...........................................................................................................

9

4.1.

Transport

9

4.2.

Storage

10

5.

Assembly................................................................................................................................

10

5.1.

Mounting position

10

5.2.

Actuator: mount to valve

10

5.2.1.

Overview on coupling variants

10

5.2.2.

Actuator (with coupling): mount

13

6.

Electrical connection.............................................................................................................

13

6.1.

Basic information

14

6.2.

Overview of connections and wiring

15

6.3.

Connection via bayonet connector

17

6.4.

External earth connection

18

6.5.

Accessories for electrical connection

18

6.5.1.

Local controls

19

7.

Commissioning......................................................................................................................

19

7.1.

Mechanical end stop setting

19

7.1.1.

End stop CLOSED: set

20

7.1.2.

End stop OPEN: set

21

7.2.

Switch compartment: open/close

22

7.3.

End position detection: verify/set

22

7.3.1.

Setting for clockwise closing

24

7.3.2.

Setting for counterclockwise closing

25

7.4.

RWG electronic position transmitter

25

7.4.1.

Set measuring range

2

SG 04.2 – SG 10.2

Table of contents

with actuator controls MEC 03.1

Содержание SG 04.2

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды